Abstract:Thermal analysis and microstructure characterization provide information regarding material thermal profiles and microstructure formation. Wrought aluminium alloys offer significant advantages in terms of higher ultimate tensile strength (UTS) and yield strength but relatively poor fluidity properties. The objective of this experiment presented in this paper was to understand the relationship between solidification rate, metallurgical behaviour, and fraction phase growth of wrought aluminium 6061. This information was crucial and important to the foundry industry to understand the material behaviour that will help to cast wrought aluminium 6061. Thermal analysis and microstructure of wrought aluminium 6061 on different cooling conditions are present in this paper. In this work, Aluminium 6061 heated and melted in a graphite crucible at a temperature of 800°C. Two thermocouples located at the centre and 20 mm from the graphite crucible wall. Slow cooling rate condition experiment rig was developed by placing graphite crucible into a chamber with kaowool insulation. Normal cooling rate condition was developed by allowing the molten solidify at room temperature. Fast cooling rate condition was prepared by applying a forced airflow over the graphite crucible. The slow, normal, and high cooling rates were calculated at 0.03°C/s, 0.2°C/s and 0.3°C/s respectively. Cooling curve analysis was performed to predict various areas of solidification phase and fraction solid. In Addition, the microstructure formation was observed, recorded, and compared between different cooling conditions. The results show slow cooling rate condition formation of eutectic and solidus temperatures occurred far from liquidus temperature. The eutectic and solidus temperature was increased with the increment of the cooling rate. Furthermore, the DCP temperature of slow cooling rate condition at 638.3°C was the lowest while gives wider temperature range corresponding to the fraction solid percentage increment. Meanwhile, an increase in cooling rate refined the microstructure, improved the grain circularity and at the same time reduced the aspect ratio.

PENGARUH TEMPERATUR TUANG PADA PENGECORAN DAUR ULANG ALUMINIUM TERHADAP NILAI KEKERASAN

Analisis Metode Anodizing Aluminium dengan Variasi Kuat Arus sebagai Material Velg Kendaraan

PENGARUH UNSUR MAGNESIUM DAN HEAT TREATMENT PADA PERFORMA PISTON DARI VELG ALUMINIUM DENGAN ADC 12

Pengaruh Proses Equal Channel Angular Pressing Terhadap Sifat Mekanik Aluminium Silikon Dengan Suhu Anil 300°C

A research on the effect of retrogression and re-aging heat treatment on hot tensile properties of AA7075 aluminum alloys

Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061

Effect of welding environment on fatigue crack growth rate of aluminium alloy 1100

The effect of hold-melt time of micro-regime precipitation size and hardness in Al-Cu alloy

The Effect of Aluminium Injection Parameters on the Mechanical Properties of the Material Produced by High Pressure Die-Casting

Pengaruh Parameter Proses 3D Printing Terhadap Kuat Bentur Menggunakan Fiamen Polycarbonate

Effects of Heat Treatment on the Corrosion Behavior and Mechanical Properties of Aluminum Alloy 2024

Effect of temperature on anti-corrosion properties of aluminum alloy anodized by sulphuric acid

Analisis Dampak Perubahan Arus Pengelasan Terhadap Kekuatan Sambungan Las Pada Material Stainless Steel 316

Effect of Ageing Temperature on the Hardness, Microstructural and Dry Sliding Wear Performance of the Functionally Graded A356 Alloy

PENGARUH DEOXIDIZING AGENT PADA MATERIAL ADDITION LADLE FURNACE DI PT GUNUNG RAJA PAKSI, CIKARANG BARAT

The Influence of Heat Aging Treatments on the Cavitation Erosion Behavior of a Type 6082 Aluminum Alloy

Effect of welding parameters on microstructure, mechanical properties and environment

Effect of Temperature Treatment on Microstructure and Electrochemical Properties of 6061 Aluminum Alloy

Analisis Pengujian Tarik dan Sebaran unsur pada Pengelasan Aluminium – Mild Steel menggunakan Metode Cold Metal

Influence of Extrusion Temperature on the Corrosion Behavior in Sodium Chloride Solution of Solid State Recycled Aluminum Alloy 6061 Chips

The genotoxic, hepatotoxic, nephrotoxic, haematotoxic and histopathological effects in rats after aluminium chronic intoxication