Abstract:The purpose of this study is to model the functional parameters of the surface texture (ISO 13565 standard) and to choose the optimal cutting parameters when turning hard steel (16MC5) with a hardness of 52 HRC. The artificial neural network (ANN) and the gray relational analysis (GRA) method are used to model and optimize the three parameters related to the bearing length rate curve (Rpkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{pk}$$end{document}, Rkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{k}$$end{document}, and Rvkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{vk}$$end{document}). An experimental design of three factors (cutting speed VCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${V}_{C}$$end{document}, feed rate fdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$f$$end{document} and depth of cut apdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$ap$$end{document}), with five levels each, was selected according to the Taguchi L25 technique. The white ceramic cutting tool was used. The models based on neural networks are compared with that obtained by the response surface methodology (RSM). The precision and the capacity of prediction of the two methods (ANN and RSM) have been investigated. The coefficient of determination of the three predictive models of Rpkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{pk}$$end{document}, Rkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{k}$$end{document}, and Rvkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{vk}$$end{document} was found to be 99.99%, which shows the effectiveness of this technique. The GRA allowed the optimization of the cutting conditions for a minimum reduced peak height (Rpkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{pk}$$end{document}), minimum core roughness depth (Rkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{k}$$end{document}), and maximum reduced valley depth (Rvkdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${R}_{vk}$$end{document}). The combination of the optimal cutting parameters respecting the previous optimization conditions is VCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${V}_{C}$$end{document} = 96 m/min, fdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$f$$end{document} = 0.106 mm/rev and apdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$ap$$end{document} = 0.10 mm.

Application of artificial neural networks (ANN) and gray relational analysis (GRA) to modeling and optimization of the material ratio curve parameters when turning hard steel

Assessment of performance parameters in intermittent turning and multi-response optimization of machining conditions using DF, MOORA, VIKOR, and coupled NSGAII-VIKOR methods

Modeling and optimization of machining parameters to minimize surface roughness and maximize productivity when turning polytetrafluoroethylene (PTFE)

Parametric study and multi-criteria optimization during turning of X210Cr12 steel using the desirability function and hybrid Taguchi-WASPAS method

Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel

Evaluation of cutting parameters during dry turning of AISI 304 stainless steel and optimization through a modified WPCA approach

Comparative Evaluation of Coated Carbide and CBN Inserts Performance in Dry Hard-Turning of AISI 4140 Steel Using Taguchi-Based Grey Relation Analysis

Investigation on machining of GFRP through ANOVA, DFA, and CoCoSo method combined with Taguchi approach

Optimization of machining parameters while turning AISI316 stainless steel using response surface methodology

Mathematical Modelling and Multiresponse Optimization to Minimise Surface Roughness in Drilling Custom 450 Stainless Steel

An integrated study of surface roughness for modelling and optimization of cutting parameters during end milling operation

Experimental Investigation and Statistical Evaluation of Optimized Cutting Process Parameters and Cutting Conditions to Minimize Cutting Forces and Shape Deviations in Al6026-T9

Experimental Optimization of High-precision Turning Parameters of AL6061 Materials for Automotive Industry Based on Grey Relational Analysis

Performance Analysis Of Aisi 4340 Hardened Steel In Dual Jet Mql Turning System: A Comparison Study Between Cvd And Pvd-Coated Carbide Tools

Multi performance optimization in machining of EN31-535A99SS with interchangeable straight cemented tungsten carbide-cobalt mixed (WC–Co) insert grade (CSTC—K20) using Taguchi coupled grey relational analysis

Multiobjective Optimization of Hard Turning on OHNS Steel Using Desirability and TOPSIS Approaches

Multi-objective optimization based on machine learning and non-dominated sorting genetic algorithm for surface roughness and tool wear in Ti6Al4V turning

Optimized Material Removal and Tool Wear Rates in Milling API 5ST TS-90 Alloy: AI-Driven Optimization and Modelling with ANN, ANFIS, and RSM

Optimization of Grinding Parameters of Tool Steel by the Soft Computing Technique

Tool vibration, surface roughness, cutting power, and productivity assessment using RSM and GRA approach during machining of Inconel 718 with PVD-coated carbide tool

A Closer Look at Precision Hard Turning of AISI4340: Multi-Objective Optimization for Simultaneous Low Surface Roughness and High Productivity