Abstract:Abstract Introduction Autologous skin cell suspensions (ASCS) are useful for treating burn wounds, including in adjunct with split thickness skin grafts (STSG) for full thickness injuries. Careful wound care is crucial after ASCS application to prevent leakage out of the wound bed. Solution blow spinning (SBS) can be used to spray polymer fiber mats with varied flexibility, adhesion, and absorption. Wounds treated with ASCS and SBS dressings demonstrate equivalent re-epithelialization as those treated conventionally. SBS polymers are currently applied using commercial airbrushes with limited control of sterility, pressure, and deposition rate, and have only been evaluated when applied after ASCS. This work investigates a novel SBS prototype designed to address these limitations and simultaneously spray cells and dressings. Methods A SBS prototype was engineered combining a 3D printed, biocompatible, disposable dual-chambered nozzle, a reusable handheld module with programmable motorized actuators, and a pressure gauge connected to an external air source. The polymers poly(lactide-co-caprolactone) (PLCL), which exhibits excellent adhesion in moist environments, and poly(lactic-co-glycolic) acid (PLGA), which conforms to irregular surfaces as a protective layer, were chosen for initial testing. Six mm full-thickness punch biopsies were created on the dorsal aspect of C57/BL/6 mice and stented (Fig 1b). ASCS was prepared from donor mouse skin and viability was tested before and after spraying at 3, 10, and 30 PSI. Wounds were dressed with either conventional transparent film adhesive dressing (Fig 1c), polymers sprayed using the device, ASCS+polymers sprayed using the device (1e), or ASCS+polymers sprayed using an airbrush (1f). Wounds were harvested on postoperative day 5, formalin fixed and paraffin embedded. Six μm sections were stained with hematoxylin and eosin (H&E), imaged (Fig 2a). Epithelial tongue length was measured by a blinded assessor. Results ASCS cell viability was 47.3±8.3% at baseline and was only significantly decreased after spraying at 30 PSI (12.2±11.0%). Hence, 10 PSI was used for the mouse experiment (Fig 2b). Overall, there were no significant differences in epithelial tongue length between the wounds treated with different cell and polymer-based dressings (Fig 2c). Conclusions The SBS prototype can be used to spray ASCS at pressures up to 10 PSI without significant loss of viability. The novel device was able to co-spray ASCS and polymers onto a wound bed. Wounds dressed with SBS polymers demonstrate equivalent epithelial tongue length at post-wound day 5 compared with wounds treated with transparent film dressing and airbrush controls. Applicability of Research to Practice Currently, ASCS and dressing application are performed in a stepwise fashion, which allows the ASCS to leak out of the wound bed. A simultaneous application process could limit ASCS loss, streamline the wound care procedure and improve healing outcomes.

Methodologies of Autologous Skin Cell Spray Graft

The Current Challenges on Spray-Based Cell Delivery to the Skin Wounds

Perspectives on the Current State of Bioprinted Skin Substitutes for Wound Healing

Regenerative Medicine Approaches for Skin Wound Healing: from Allografts to Engineered Skin Substitutes

528 Efficacy of Autologous Skin Cell Suspension in the Closure of Thermal and Non-thermal Full-thickness Wounds

A novel method for the establishment of autologous skin cell suspensions: characterisation of cellular sub-populations, epidermal stem cell content and wound response-enhancing biological properties

71 A Novel Solution-Blow-Spinning Device Co-Sprays Autologous Skin Cell Suspensions and Polymer for Full Thickness Wounds

806 Autologous Skin Cell Suspension Demonstrates Successful Outcomes in the Treatment of Burn and Wound Sites

Development and Application of a Mechanical Arm-Based in Situ 3D Bioprinting Method for the Repair of Skin Wounds

Skin Substitutes and Wound Healing: Current Status and Challenges

Autologous Epidermal Cell Suspension: A Promising Treatment for Chronic Wounds.

In Situ Bioprinting of Autologous Skin Cells Accelerates Wound Healing of Extensive Excisional Full-Thickness Wounds

Bioengineering skin using mechanisms of regeneration and repair

Advanced drug delivery systems and artificial skin grafts for skin wound healing

Tissue Engineered Skin and Wound Healing: Current Strategies and Future Directions

Developing a bioink for single-step deposition and maturation of human epidermis

Review Article Tissue-engineered skin: bottleneck or breakthrough

"Minimally Invasive" Skin Grafting With Enzymatic Debridement and Autologous Skin Cell Spray: A Retrospective Case Series

Benefits of Aerosolized, Point-of-care, Autologous Skin Cell Suspension (ASCS) for the Closure of full Thickness Wounds from Thermal and Non-Thermal Causes

Clinical Translational Potential in Skin Wound Regeneration for Adipose-Derived, Blood-Derived, and Cellulose Materials: Cells, Exosomes, and Hydrogels

Innovative Treatment Strategies to Accelerate Wound Healing: Trajectory and Recent Advancements