Abstract:ABSTRACT Introduction The recent COVID-19 pandemic has underscored the necessity of protecting health care providers (HCPs) against the transmission of infectious agents during dental procedures. To this end, the effectiveness of several air cleaning devices (ACDs) in reducing HCPs exposure to aerosols generated during dental procedures was estimated, separately or in combination with each other. These ACDs were a chairside unit capturing aerosols at the source of generation, and four ambient ACDs: a portable ambient ACD; a negative pressure module; a custom made, fan-operated and wall-mounted air filter (WMAF); and a smaller and passive version of the latter. The last three ACDs were intended for mobile dental clinics (MDCs) only. Materials and Methods This assessment was performed in two different environments: in a dental clinic operatory and in a MDC. Two dental personnel, acting in the roles of dentist and dental assistant, performed on simulated patient aerosol-generating and non-aerosol-generating procedures. For each 5-minute scenario, the cumulative exposure to airborne particulate matter 10 μm in size or smaller (PM10) was determined by calculating the sum of all 1 second readings obtained with personal and ambient air monitors. The effectiveness of the ACDs in capturing PM10 was estimated based on the capability of the ACDs to keep PM10 level at or below the initial background level. Results In all conditions assessed in the dental clinic operatory, when both the chairside and portable ambient ACDs were functioning, an estimated effectiveness of 100% in capturing PM10 was achieved. In the MDC, in all conditions where the chairside ACD was used without the negative pressure module, an estimated effectiveness of 100% was also achieved. The simultaneous operation of the negative pressure module in the MDC, which led to a room negative pressure of −0.25 inch wc, reduced the chairside ACD’s effectiveness in capturing aerosols. Conversely, the use of the WMAF in the MDC in combination with the chairside ACD further reduced exposure to PM10 below the initial background level. Nonetheless, in all conditions assessed in both settings (dental clinic operatory and MDC), larger visible aerosols were produced, often landing on the surrounding environment. A fair portion of these aerosols landed on the inside of the chairside ACD flange. Conclusions This assessment suggests that the use of the tested chairside ACD, by capturing aerosols at the source of generation, had the greatest impact on reducing exposure of dental personnel to PM10 produced during dental procedures. This study also indicates that such exposure is further reduced with the addition of an ambient ACD. However, creating a negative pressure room as high as −0.25 inch wc can lead to air turbulence reducing the effectiveness of ACDs in capturing aerosols at the source. Furthermore, the presence of uncaptured droplets and spatter on the surrounding environment supports the need to complement the use of engineering controls with proper administrative controls and personal protective equipment, as recommended by governmental agencies and the scientific community for preventing the transmission of infection in health care settings.

Design and quantitative evaluation of ‘Aerosol Bio-Containment Device (ABCD)’ for reducing aerosol exposure during infectious aerosol-generating events

Development of a new Aerosol Barrier Mask for mitigation of spread of SARS-CoV-2 and other infectious pathogens

Effectiveness of a suction device for containment of pathogenic aerosols and droplets

Aerosol containment device for airway management of patients with COVID-19: a narrative review

An overview of COVID-19 aerosol box for preventing droplet and aerosol contaminations in healthcare providers performing airway intubation

Infectious Aerosol Capture Mask as Environmental Control to Reduce Spread of Respiratory Viral Particles

Protective device to reduce aerosol dispersion in dental clinics during the COVID‐19 pandemic

In vitro model for investigating aerosol dispersion in a simulated COVID-19 patient during high-flow nasal cannula treatment

Effectiveness of Selected Air Cleaning Devices During Dental Procedures

Effectiveness of a novel semi‐closed barrier device with a personalized exhaust in cough aerosol simulation according to particle counts and visualization of particles

Methodology for Addressing Infectious Aerosol Persistence in Real-Time Using Sensor Network

A quantitative evaluation of aerosol generation during tracheal intubation and extubation

Development and validation of a patient face-mounted, negative-pressure antechamber for reducing exposure of healthcare workers to aerosolized particles during endonasal surgery

Short-Term Use Biocontainment Bubbles: Innovative Source Containment of Potentially Infectious SARS-CoV-2 Aerosols

The Spatial-Temporal Distribution and Control Measures Evaluation of Droplets and Aerosol Cloud in Dental Procedures

An apparatus for nondestructive and rapid comparison of mask approaches in defense against infected respiratory aerosols

Investigation of aerosol dispersion and air purifier performance in a hospital patient room using CFD and measurements

Computational and experimental investigation of an aerosol extraction device for use in dentistry

Use of portable air purifiers to reduce aerosols in hospital settings and cut down the clinical backlog

In Vivo Study of Aerosol, Droplets and Splatter Reduction in Dentistry