Abstract:Three-dimensional (3D) cell-printing has been emerging as a promising technology with which to build up human skin models by enabling rapid and versatile design. Despite the technological advances, challenges remain in the development of fully functional models that recapitulate complexities in the native tissue. Moreover, although several approaches have been explored for the development of biomimetic human skin models, the present skin models based on multistep fabrication methods using polydimethylsiloxane chips and commercial transwell inserts could be tackled by leveraging 3D cell-printing technology. In this paper, we present a new 3D cell-printing strategy for engineering a 3D human skin model with a functional transwell system in a single-step process. A hybrid 3D cell-printing system was developed, allowing for the use of extrusion and inkjet modules at the same time. We began by revealing the significance of each module in engineering human skin models; by using the extrusion-dispensing module, we engineered a collagen-based construct with polycaprolactone (PCL) mesh that prevented the contraction of collagen during tissue maturation; the inkjet-based dispensing module was used to uniformly distribute keratinocytes. Taking these features together, we engineered a human skin model with a functional transwell system; the transwell system and fibroblast-populated dermis were consecutively fabricated by using the extrusion modules. Following this process, keratinocytes were uniformly distributed onto the engineered dermis by the inkjet module. Our transwell system indicates a supportive 3D construct composed of PCL, enabling the maturation of a skin model without the aid of commercial transwell inserts. This skin model revealed favorable biological characteristics that included a stabilized fibroblast-stretched dermis and stratified epidermis layers after 14 days. It was also observed that a 50 times reduction in cost was achieved and 10 times less medium was used than in a conventional culture. Collectively, because this single-step process opens up chances for versatile designs, we envision that our cell-printing strategy could provide an attractive platform in engineering various human skin models.

Recombinant Human Collagen-Based Bioinks for the 3D Bioprinting of Full-thickness Human Skin Equivalent

Establishing a Novel 3D Printing Bioinks System with Recombinant Human Collagen.

Advances in the Research of Bioinks Based on Natural Collagen, Polysaccharide and Their Derivatives for Skin 3D Bioprinting

Three-dimensional Bioprinting of a Full-Thickness Functional Skin Model Using Acellular Dermal Matrix and Gelatin Methacrylamide Bioink

Fibrinogen-Based Bioink for Application in Skin Equivalent 3D Bioprinting

Preparation of Chitosan/Recombinant Human Collagen-Based Photo-Responsive Bioinks for 3D Bioprinting

Simple and robust 3D bioprinting of full-thickness human skin tissue

Marine Collagen-Based Bioink for 3D Bioprinting of a Bilayered Skin Model

Properties of Collagen/Sodium Alginate Hydrogels for Bioprinting of Skin Models

Bioprinted Gelatin-Recombinant Type III Collagen Hydrogel Promotes Wound Healing

[Advances in the research of application of collagen in three-dimensional bioprinting]

3D Cell Printing of in Vitro Stabilized Skin Model and in Vivo Pre-Vascularized Skin Patch Using Tissue-Specific Extracellular Matrix Bioink: A Step Towards Advanced Skin Tissue Engineering

Direct 3D cell-printing of human skin with functional transwell system

Extracellular‐Matrix‐Reinforced Bioinks for 3D Bioprinting Human Tissue

A potential dermal substitute using decellularized dermis extracellular matrix derived bio-ink

Characterization and application of photocrosslinkable collagen maleate as bioink in extrusion-based 3D bioprinting

Tyrosinase-doped Bioink for 3D Bioprinting of Living Skin Constructs

High-Resolution Bioprinting of Recombinant Human Collagen Type III

Characterization of Recombinant Humanized Collagen Type III and Its Influence on Cell Behavior and Phenotype

Optimization of collagen type I-hyaluronan hybrid bioink for 3D bioprinted liver microenvironments