Abstract:Lattice structures are bio-inspired designs made up of repeated unit cells consisting of beams, surfaces, or plates that fit together in an ordered or stochastic fashion. These unit cells are configured according to their size and shape in three dimensions. Simple lattices can be created using standard manufacturing techniques such as computer numerical control machining, welding, and casting. Additive manufacturing enables customers to make complex structures with small features at a reasonable cost. In the present work, using octagon, hexagrid, and rhombic dodecahedron lattice topologies, characterized by unit cell size from 3 × 3 × 3 to 7 × 7 × 7 mm and strut thickness from 0.5 to 1.5 mm, the structural behavior of a solid cylindrical model made of polylactic acid material under compression is analyzed. Finite element analysis (FEA) through Autodesk® Netfabb® solvers was used to assess lattice structure mechanical and structural properties. The results were validated by physical compression testing on additively manufactured samples. Cellular designs with 3 × 3 × 3 mm unit cells and 1.5 mm strut thickness displayed the lowest Von Mises stress and deformation. For different topologies, lowest results were rhombic dodecahedron (stress through FEA as 61.3108 MPa and stress through physical test as 61.05 MPa, deformation through FEA as 0.49921 mm and deformation through physical test as 0.48 mm), octagon (stress through FEA as 77.4147 MPa and stress through physical test as 76.92 MPa, deformation through FEA as 0.53316 mm and deformation through physical test as 0.51 mm), and for hexagrid (stress through FEA as 62.2911 MPa, stress through physical test as 62.15 MPa, deformation through FEA as 0.81997 mm and deformation through physical test as 0.81 mm). The percentage error between the stress through FEA and stress through physical test for octagon, hexagrid, and rhombic dodecahedron lattice topology was found out to be 0.63, 0.22, and 0.43%, respectively. Corresponding percentage deformation error between deformation through FEA and deformation through physical test was also found out to be 4.343, 2.435, and 3.848%, respectively. In addition, the impacts of volume reduction, surface area of the lattice, and relative density were explored pertaining to the structural behavior of the lattice. As a result of the examination into mechanical qualities based on these criteria, rhombic dodecahedron lattice topology with 3 × 3 × 3 mm unit cell size and strut thickness of 1.5 mm was found to be a better choice than octagon and hexagrid lattice topologies for 3D printing components that were loaded under axially compressive loads.

Compression Behavior of Pilar Octahedral Lattice Structures

Quasi-static Compressive Behaviors of Large-Size Titanium Lattice Sandwich Structure Based on Pulse Hot-Wire Arc Additive Manufacturing

Lattice Structures—Mechanical Description with Respect to Additive Manufacturing

Experimental and numerical investigation of PLA based different lattice topologies and unit cell configurations for additive manufacturing

Mechanical Behaviors of SLM Additive Manufactured Octet-Truss and Truncated-Octahedron Lattice Structures with Uniform and Taper Beams

A Study on the Compressive Behavior of Additively Manufactured AlSi10Mg Lattice Structures

The coupled effect of aspect ratio and strut micro-deformation mode on the mechanical properties of lattice structures

Compressive properties of AlSi10Mg lattice structures with novel BCCZZ and FCCZZ configurations fabricated by selective laser melting

Compression and Tensile Testing of L-PBF Ti-6Al-4V Lattice Structures with Biomimetic Porosities and Strut Geometries for Orthopedic Implants

Compression behavior of strut-reinforced hierarchical lattice—Experiment and simulation

Generative design and mechanical properties of the lattice structures for tensile and compressive loading conditions fabricated by selective laser melting

Compressive Behavior of Novel Additively Manufactured Ti-6Al-4V Lattice Structures: Experimental and Numerical Studies

Mechanical Properties of Lattice Structures with a Central Cube: Experiments and Simulations

Mechanical characterization of additively-manufactured metallic lattice structures with hollow struts under static and dynamic loadings

Improving energy absorption and failure characteristic of additively manufactured lattice structures using hollow and curving techniques

Heterogeneous compressive responses of additively manufactured Ti-6Al-4V lattice structures by varying geometric parameters of cells

Flexural Behavior of 3D-Printed Carbon Fiber-Reinforced Nylon Lattice Beams

Compression Behavior of 316L Lattice Structures Produced by Indirect Additive Manufacturing

Experimental and numerical investigations on uniaxial-stress ductility failure of additive manufactured lattice structures based on frequency fatigue technique

Compressive properties of imperfect Ti-6Al-4V lattice structure fabricated by electron beam powder bed fusion under static and dynamic loadings

Effective Mechanical Properties of Additive Manufactured Strut‐Lattice Structures: Experimental and Finite Element Study