Abstract:<div class="section abstract"><div class="htmlview paragraph">Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode. The findings demonstrate that ammonia-PODE3 mode exhibits better ignition characteristics than ammonia-diesel mode, resulting in an earlier ignition start, a larger flame area, a larger flame expansion speed, a shorter ignition delay time (IDT) and a shorter combustion duration (CD) due to the higher cetane number (CN) and a greater injection mass of PODE3 at the same energy input. Ammonia-PODE3 mode achieves larger maximum cylinder pressure (Pmax) and peak heat release rate (HRR) compared to ammonia-diesel mode. Furthermore, almost no soot was observed in ammonia-PODE3 mode throughout the entire combustion process. The results also indicate the start of the ignition is delayed and the first peak flame expansion speed decreases at a higher ammonia energy ratio. The maximum flame area is the largest at ERa = 60%, but the peak cylinder pressure and IMEP reach their highest values at ERa = 50%. Both the first peak flame area and the first peak flame expansion speed increase with the increase of ERInj1, and the Pmax and first peak HRR also increase. The IDT slightly extends with the increase of ERInj1, while CA50 advances and CD reduces. The start of the ignition is delayed with the advancement of the main injection time, and the largest flame area is observed at SOI1 = -12.5 °CA. Both the first Pmax and the maximum IMEP occur at SOI1 = -15 °CA. This is because the cylinder temperature and pressure are lower during combustion when the main injection time is early, while a later main injection time leads to inadequate fuel-air mixing and a delayed combustion phase.</div></div>

Study on dual injection strategy of diesel ignition ammonia/hydrogen mixture fuel engine

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Study on Combustion and Emission Performance of Dual Injection Strategy for Ammonia/Hydrogen Dual-Fuel Engine

Performance characteristics of a two-stroke low speed engine applying ammonia/diesel dual direct injection strategy

Simulation Research on the Injection Strategy of a Diesel-Ammonia Dual-Fuel Marine Engine

Experimental study on the effects of pilot injection strategy on combustion and emission characteristics of ammonia/diesel dual fuel engine under low load

Numerical Investigation into the Characteristics of Fuel-Borne Nitrogen Pollutants in Ammonia-Diesel Dual Fuel Engines Through Implementing Atmospheric Nitrogen Unreactivity

Parametric analysis and optimization of the combustion process and pollutant performance for ammonia-diesel dual-fuel engines

Exploring the GHG reduction potential of pilot diesel-ignited ammonia engines - Effects of diesel injection timing and ammonia energetic ratio

Potential of ammonia energy fraction and diesel pilot-injection strategy on improving combustion and emission performance in an ammonia-diesel dual fuel engine

Optimizations of energy fraction and injection strategy in the ammonia-diesel dual-fuel engine

Numerical analysis for optimizing combustion strategy in an ammonia-diesel dual-fuel engine

Comparison and optimization of strategies for ammonia-diesel dual-fuel engine based on reactivity assisted jet ignition and reactivity turbulent jet disturbance under high load conditions

A comparison between low- and high-pressure injection dual-fuel modes of diesel-pilot-ignition ammonia combustion engines

Effects of Pre-Injection Strategy on Combustion Characteristics of Ammonia/Diesel Dual-Fuel Compression Ignition Mode

Experimental investigation of the effect of ammonia substitution ratio on an ammonia-diesel dual-fuel engine performance

A Study on Combustion and Emission Characteristics of an Ammonia-Biodiesel Dual-Fuel Engine

Evaluation of hydrogen injection and oxygen enrichment strategies in an ammonia-hydrogen dual-fuel engine under high compression ratio

Optical diagnostic study on ammonia-diesel and ammonia-PODE dual fuel engines

Numerical analysis and optimization of combustion and emissions in an ammonia-diesel dual-fuel engine using an ammonia direct injection strategy

Optical investigation on effects of diesel injection strategy on ammonia/diesel dual fuel combustion characteristics and flame development