Abstract:Highly-conductive nanostructures may be dispersed into phase change materials (PCM) to improve their effective thermal conductivity, thus leading to colloidal systems that are referred to as nanostructure-enhanced PCM (NePCM). Results of a theoretical and experimental investigation on freezing of NePCM in comparison to the base PCM are presented. A one-dimensional Stefan model was developed to study the unidirectional freezing of NePCM in a finite slab. Only the thermal energy equation was considered and the presence of static dispersed nanoparticles was modeled using effective media relations. A combination of analytical and integral methods was used to solve this moving boundary problem. The elapsed time to form a given thickness of frozen layer was therefore predicted numerically. A cooled-from-bottom unidirectional freezing experimental setup was designed, constructed, and tested. Thermocouple readings were recorded at several equally spaced locations along the freezing direction in order to monitor the progress of the freezing front. As an example, cyclohexane (C6H12) and copper oxide (CuO) nanoparticles were chosen to prepare the NePCM samples. The effective thermophysical and transport properties of these samples for various particle loadings (0.5/3.8, 1/7.5, and 2/14.7 vol. %/wt. %) were determined using the mixture and Maxwell models. Due to utilization of the Maxwell model for thermal conductivity of both phases, the numerical predictions showed that the freezing time is shortened linearly with increasing particle loading, whereas nonmonotonic expediting was observed experimentally. The maximum expediting was found to be nearly 8.23% for the 0.5 vol. % sample. In the absence of a nanoparticle transport model, the mismatch of the cold plate boundary conditions, lack of accurate thermophysical properties, especially in the solid phase of NePCM samples and precipitation issues with 2 vol. % samples were addressed by improving the experimental setup. Through adopting a copper cold plate, utilizing measured thermal conductivity data for both phases and using 1, 2, and 4 wt. % samples, good agreement between the experimental and numerical results were realized. Specifically, adoption of measured thermal conductivity values for the solid phase in the Stefan model that were originally underestimated proved to be a major cause of harmony between the experiments and predictions. [DOI: 10.1115/1.4006305]

Numerical investigation of a non-linear moving boundary problem describing solidification of a phase change material with temperature dependent thermal conductivity and convection

Expedited Freezing of Nanoparticle-Enhanced Phase Change Materials (nepcm) Exhibited Through A Simple 1-D Stefan Problem Formulation

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

A Theoretical and Experimental Investigation of Unidirectional Freezing of Nanoparticle-Enhanced Phase Change Materials

Heat transfer analysis describing freezing of a eutectic system by a line heat sink with convection effect in cylindrical geometry

A low Mach enthalpy method to model non-isothermal gas-liquid-solid flows with melting and solidification

Enhanced numerical modeling of natural heat convective phase change for generalized non-Newtonian fluids at high Rayleigh number

Numerical Modeling Of Phase-Change And Heat-Transfer During Rapid Solidification Processes - Use Of Control Volume Integrals With Element Subdivision

Numerical Investigation of Heat Transfer in Wire and Tube based Phase Change Material Heat Exchanger

A consistent, volume preserving, and adaptive mesh refinement-based framework for modeling non-isothermal gas-liquid-solid flows with phase change

Thermal modelling of DC continuous casting including submould boiling heat transfer

Solidification analysis of a single particle with encapsulated phase change materials

An analytical solution for a phase change nano-capsule cooled by forced convection

Enthalpy-based immersed boundary-lattice Boltzmann model for solid-liquid phase change in porous media under local thermal non-equilibrium condition

Verification of a binary fluid solidification model in the finite-volume flow solver

A monolithic model of solid–liquid phase change problem

Numerical Simulation of Convection in the Two-Phase Zone of a Binary Alloy

Two-phase numerical simulation of thermal and solutal transport exploration of a non-Newtonian nanomaterial flow past a stretching surface with chemical reaction

NUMERICAL CALCULATION FOR LATENT HEAT RELEASES IN ALLOY CASTINGS OF ANY SOLIDIFICATION RANGE USING AN EXTENDED TEMPERATURE-COMPENSATION METHOD

Interface-resolved simulation of solid-liquid phase change with thermal convection using discrete unified gas kinetic scheme

A level-set formulation to simulate diffusive solid/solid phase transformation in polycrystalline metallic materials -- Application to austenite decomposition in steels