Preparation and Evaluation of Caffeine Orodispersible Films: The Influence of Hydrotropic Substances and Film-Forming Agent Concentration on Film Properties

Robert-Alexandru Vlad,Andrada Pintea,Mădălina Coaicea,Paula Antonoaea,Emőke Margit Rédai,Nicoleta Todoran,Adriana Ciurba

DOI: https://doi.org/10.3390/polym15092034

IF: 5

2023-04-26

Polymers

Abstract:This study aimed to develop caffeine (CAF) orodispersible films (ODFs) and verify the effects of different percentages of film-forming agent and hydrotropic substances (citric acid—CA or sodium benzoate—SB) on various film properties. Hydroxypropyl methylcellulose E 5 (HPMC E 5) orodispersible films were prepared using the solvent casting method. Four CAF-ODF formulations were prepared and coded as CAF1 (8% HPMC E 5, CAF), CAF2 (8% HPMC E 5 and CAF:CA–1:1), CAF3 (9% HPMC E 5 and CAF:CA–1:1), and CAF4 (9% HPMC E 5 and CAF:SB–1:1). The CAF-ODFs were evaluated in terms of disintegration time, folding endurance, thickness, uniformity of mass, CAF content, thickness-normalized tensile strength, adhesiveness, dissolution, and pH. Thin, opaque, and slightly white CAF-ODFs were obtained. All the formulations developed exhibited disintegration times less than 3 min. The dissolution test revealed that CAF1, CAF2, and CAF3 exhibited concentrations of active pharmaceutical ingredients (APIs) released at 30 min that were close to 100%, whilst CAF4 showed a faster dissolution behaviour (100% of the CAF was released at 5 min). Thin polymeric films containing 10 mg of CAF/surface area (3.14 cm2) were prepared.

polymer science

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to develop new caffeine - containing oral disintegrating films (ODFs) and study the effects of different concentrations of film - forming agents and solubilizing substances on the properties of these films. Specifically, the authors aim to:

1. **Develop new caffeine - containing oral disintegrating films (CAF - ODFs)**: To meet the needs of pediatric and elderly patients, who usually have difficulty swallowing solid drug dosage forms. Oral disintegrating films can dissolve quickly in the mouth and can be taken without water, improving patient compliance.

2. **Evaluate the effects of different components on film properties**: By changing the ratios of film - forming agents (such as hydroxypropyl methylcellulose E 5, HPMC E 5) and solubilizing substances (such as citric acid - CA and sodium benzoate - SB), study the effects of these changes on the physical and mechanical properties of the films (such as disintegration time, folding durability, thickness, mass uniformity, caffeine content, thickness - normalized tensile strength, adhesiveness, solubility and pH value).

3. **Optimize the film formulation**: Find the best combination of components so that the prepared films have ideal characteristics, such as rapid disintegration, good mechanical strength and moderate adhesiveness, thereby improving drug release efficiency and patient acceptance.

### Formula summary

A key formula involved in the article is used to calculate the thickness - normalized tensile strength (TS), and its expression is as follows:

\[
TS\ (\text{N·mm}^{-2})=\frac{M\times g}{W\times T}
\]

where:
- \(TS\) — thickness - normalized tensile strength (N·mm\(^{-2}\))
- \(M\) — total weight when the sample breaks (g)
- \(g\) — gravitational acceleration (9.81 N·kg\(^{-1}\))
- \(W\) — sample width (mm)
- \(T\) — average sample thickness (mm)

Through this formula, researchers can quantify the mechanical strength of the films to ensure their reliability and safety in practical applications.