Abstract:Wire arc additive manufacturing (WAAM) technology is widely used in the fields of aerospace, shipbuilding, and automobile industry due to the advantages of fast forming speed, high material utilization and low production cost. WAAM is extremely sensitive to parameters, and different processes and materials produce different deposition effects and properties. Therefore, it is of great significance to study the WAAM formability of various materials. Herein, the microstructure, mechanical properties, and galvanic corrosion behavior of the low-carbon high-strength steel (10CrNi3MoV) fabricated by cold metal transfer (CMT) WAAM technology were investigated. The single-channel multilayer deposition parts were prepared by reciprocating deposition, and the forming parts were divided into six zones by observing the different positions of the structure: matrix, heat-affected zone, remelting zone, initial deposition zone, interlayer zone, and interlayer bonding zone. Electron backscattered diffraction (EBSD) analysis showed that the amount of recrystallization and substructure in the deposition layer had no obvious change, and the texture phenomenon was the most obvious in the initial deposition zone of the pole map reaction. The texture phenomenon gradually weakened with the increase of the deposition layers. The microhardness from the matrix to the deposition stable zone was tested. The hardness of the matrix changed smoothly, that of the heat-affected zone was the largest, and that of the deposition layer was 221–282 HV0.2. The tensile properties were tested in different directions and angles, and the yield strength and tensile strength of the deposited layer were more than 550 MPa and 760 MPa, respectively. The galvanic corrosion behavior between the deposited layer and the matrix was investigated, and the polarization curve showed that the corrosion potential of the deposited layer was lower than that of the matrix, and the corrosion current density of the deposited layer was higher than that of the matrix.

Gradient Wire and Arc Additive Remanufacturing of 5CrNiMo Hot Forging Die: Microstructure, Mechanical Properties, and Applications

Microstructure and Mechanical Properties of Gradient Interfaces in Wire Arc Additive Remanufacturing of Hot Forging Die Steel

Research on gradient additive remanufacturing of ultra-large hot forging die based on automatic wire arc additive manufacturing technology

Filling Path Planning and Polygon Operations for Wire Arc Additive Manufacturing Process

In-situ remanufacturing of forging dies for automobile parts based on wire arc directed energy deposition

Wire and arc additive remanufacturing of hot-forging dies: a preliminary study

Study on the Complex Strengthening Processes of 5cr2nimovsi Steel Large Hot Forging Dies

Combined Strengthening Process of 5cr2nimovsi Steel Large Hot Forging Dies

Microstructure and Mechanical Properties of NiCrMoV Steel Fabricated by Double-Electrode Gas Metal Arc Additive Manufacturing

Research on Transition Layer Microstructure and Properties of Al–Cu/Al–Si Gradient Materials Fabricated by Cold Metal Transfer

A novel high-dynamic actuator based in-situ micro-forging process for wire arc additive manufacturing of aluminum alloy

Manufacture and Properties on Prototype for Multi-metal Hot Forging Die Based on Cobalt Alloy Coating

Path Generation Strategy and Wire Arc Additive Manufacturing of Large Aviation Die with Complex Gradient Structure

Study on High-Temperature Constitutive Model and Plasticity of the Novel Cr-Mo-V Hot-Work Die Steel Forging

Hot Deformation Behaviour of Additively Manufactured 18Ni-300 Maraging Steel

Optimizing the Morphology of Primary Carbides and Mechanical Properties during Processing Of Cast-Steel (Din Gx210crv12 1) Press-Forming Dies

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Study on Compound Strengthening Process for Large Hot Forging Die of 5crnimo Steel

Microstructure, Mechanical Properties, and Galvanic Corrosion of 10CrNi3MoV Fabricated by Wire Arc Additive Manufacturing

Influence of Heat Flow on the Grain Morphology and Porosity of Wire Arc Additive Manufactured 2319 Aluminum Alloy

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials