Abstract:Air bubble injection has recently been confirmed as a beneficial technique for enhancing the thermal performance of a heat exchanger. The normal vertical motion of the bubbles due to buoyancy force leads to the entrainment of fluid from the shell side, thereby raising its velocity and turbulence level whilst improving the mix within the shell. Consequently, the thermal boundary layer that formed around the outer surface of the coil is disrupted, thus reducing heat transfer resistance and enhancing the heat transfer rate. Despite relatively considerable attention that has been given to assess this technique, numerous investigations have concentrated on only a few operational conditions. This consideration will be insufficient to understand the influence of air injection entirely on the thermal performance of a heat exchanger. Thus, this study aims to fill this gap by performing experiments over numerous operational conditions for hot and cold fluids and the injected air in a vertical counter-current coiled tube heat exchanger. The optimal air flow and the shell-side flow rates of the vertical coiled tube heat exchanger are determined, thus leading to the economic operation of a heat exchanger. Therefore, the implemented shell-side flow, air flow and coil-side flow rates were changed from 2 LPM to 10 LPM, from 0 to 10 LPM and from 1 LPM to 2 LPM, respectively, with three temperature differences (i.e. 20°C,30°Cand36°C). The number of heat transfer units (NTU) and the thermal effectiveness of the heat exchanger were investigated intensively. Results showed that the NTU and the effectiveness are influenced significantly by the injected air flow, shell-side flow and coil-side flow rates without noticeable effect on the temperature difference. In addition, the positive role of the injected air flow rate was diminished, and no further enhancement of NTU and effectiveness was observed when Qa>6LPM. The most effective shell-side flow rate was also 6 LPM. The maximum augmentation in the NTU and the effectiveness were 1.93 and 0.83, correspondingly, whilst the minimum value of the NTU and the effectiveness were 0.66 and 0.63, respectively.

Energy, exergy, and economic (3E) analysis of air bubbles injection into plate heat exchangers

Numerical Study on Hydrodynamics, Mixing and Heat Transfer of Highly Viscous Fluid in a Novel Shell-and-tube Heat Exchanger with X-type Baffles

Critical Comparison of Electrostatic Effects on Hydrodynamics and Heat Transfer in a Bubbling Fluidized Bed with a Central Jet

Energy and Exergy Efficiency Analysis of Solar Driven Ejector–compressor Heat Pump Cycle

Optimisation and evaluation of NTU and effectiveness of a helical coil tube heat exchanger with air injection

Exergy Efficiency Design For Multi-Stream Plate-Fin Heat Exchangers Based On Entropy Generation Assessment

Flow Boiling in Dimpled Plate Heat Exchangers with Different Geometric Parameters: Analysis of Asymmetric Channels

Heat transfer augmentation in a double pipe heat exchanger by tandem utilization of bubble injection and novel magnetic turbulators methods

Enhancement of heat transfer in a vertical shell and tube heat exchanger using air injection and new baffles: Experimental and numerical approach

Study on performance of horizontal single pass shell and multi-tube heat exchanger with baffles by air bubble injection

A numerical analysis of heat transfer in a cross-current heat exchanger with controlled and newly designed air flows

Experimental investigation of the performance attributes of a double pipe heat exchanger equipped with baffles of conventional or flower layouts

Exergy and exergoenvironmental analyses for characterizing heat transfer and pressure drop of any heat exchanger

First and second law analysis of a heat exchanger equipped with perforated wavy strip turbulator in the presence of Water-CuO nanofluid

Three-dimensional analysis for optimizing thermo-hydrodynamic performance of heat exchangers with perforated semi-circular inserts

Second law efficiency analysis of air injection into inner tube of double tube heat exchanger

Energy, exergy, and exergoeconomic analyses of an air source transcritical CO 2 heat pump for simultaneous domestic hot water and space heating

Theoretical and experimental investigation of a heat pipe heat exchanger for energy recovery of exhaust air

Experimental Investigation on the Thermal Performance of Pulsating Heat Pipe Heat Exchangers

Thermodynamic evaluation of shell and tube heat exchanger through advanced exergy analysis

Effect of Airflow Non-Uniformities on the Thermal Performance of Water–Air Heat Exchangers—Experimental Study and Analysis