Abstract:Active materials used in lithium ion batteries consist of micro-metric ceramic particles. Mechanical failure can happen within these brittle particles due to large internal stresses provoked by lithium intercalating in the crystalline structure during charge and discharge. Their mechanical behavior is directly related to some key intrinsic parameters, namely the elastic modulus, the fracture toughness and lithium di usivity. This works deals with the development of new characterization techniques to quantify these parameters at the local scale. Obtaining quantitative measurements is notably challenging for this type of specimen due to the highly heterogeneous structure of battery electrodes. For this, spinel LiMn2O4-based commercial cathodes are proposed as material of investigation. First, composition analysis of cathode materials at di erent states of charge was done. In general it was noticed that commercial cells are not as consistent as laboratory cells: impurities are often present (Ni, Co,...) and particles can be porous agglomerates of nanoparticles as well as large single grains. However only spinel structure was detected by X-ray di raction and Rietveld analysis showed a typical lattice expansion for higher lithium concentrations. A method using nanoindentation was developed. It consists of applying a large number of indents in cathode cross-sections and subsequently ltering the measurements depending on whether they t the set of hypotheses of the Oliver and Pharr method. It was observed that for decreasing lithium concentrations, the elastic modulus and the hardness increase from 87 GPa (0% State of Charge) to 104 GPa (100% SoC) and from 7.0 GPa (0% SoC) to 8.0 Gpa (100%SoC), respectively. With the help of contact-resonance atomic force microscopy, the elastic property could also be qualitatively mapped and it seems that the particles are homogeneous. Added to micro-raman spectroscopy, it was observed that neighboring particles can have di erent lithiation levels. The fracture toughness was estimated by measuring the crack opening displacement by atomic force microscopy and applying Irwin’s near eld theory. A toughness of about 0.9 MPa·m was found but should not be taken at face-value. Irwin’s theory requires a purely elastic-brittle fracture with traction-free crack walls. Unfortunately this condition cannot be met due to the size of the particles and the toughness is surely overestimated. Associated with electron backscattered di raction, cleavage planes were also evaluated on a reference {111} wafer. It was found that cracks always propagate in the <121> direction, corresponding to {101} planes just below the surface. At higher depths (> 100 nm), the crack deviates of 30 to 40◦. The last part of this work consists of developing a model to better comprehend electrochemical strain microscopy “time spectroscopy” (ESM-TS). It is the most promising technique to quantify locally ionic di usion coe cients. An AFM cantilever is used

Current and deformation induced by voltage in the single LiNi0.8Co0.1Mn0.1O2 particle from atomic force microscopy technique and phase field simulation

Multi-scale Failure Behavior of Cathode in Lithium-ion Batteries Based on Stress Field

In situ characterization of Ni-rich NMC811 thin films prepared by sol-gel method using different scanning probe microscopy techniques

Lithiation of ZnO Nanowires Studied by In-Situ Transmission Electron Microscopy and Theoretical Analysis

In Situ Study of Li-ions Diffusion and Deformation in Li-rich Cathode Materials by Using Scanning Probe Microscopy Techniques

Numerical Analysis of the Cyclic Mechanical Damage of Li-ion Battery Electrode and Experimental Validation

Stress-mediated Lithiation in Nanoscale Phase Transformation Electrodes

Phase-field simulation for voltage profile of L i x S n nanoparticle during lithiation/delithiation

Direct Observation Of Defect-Aided Structural Evolution In A Nickel-Rich Layered Cathode

Unraveling the Nanoscopic Strain Evolution in Single Crystal Cathodes

Nanomechanics of Li-ion battery materials

Operando chemo-mechanical evolution in LiNi0.8Co0.1Mn0.1O2 cathodes

Nanoimaging of solid solution domains during phase transitions inside LiNi0.5Mn1.5O4

Nanoindentation measurements of anisotropic mechanical properties of single crystalline NMC cathodes for Li-ion batteries

Voltage induced electrochemical reactions in the single lithium-rich layer-oxide nanoparticles

Molecular dynamics method to investigate the effect of variable electric field on the first charge of Li-Ion Nanobattery with carbon anode

Multiscale strain alleviation of Ni-rich cathode guided by in situ environmental transmission electron microscopy during the solid-state synthesis

Atomic-Resolution In Situ Exploration of the Phase Transition Triggered Failure in a Single-Crystalline Ni-Rich Cathode

Electro-chemo-mechanical behavior of lithium-ion battery electrodes

Computational modeling of coupled mechanical damage and electrochemistry in ternary oxide composite electrodes

In Situ Characterization of Crystal Phase Evolution of the LiNi0.6Co0.2Mn0.2O2 Cathode at Different Current Densities