Abstract:To reduce the "shuttle effects" of lithium polysulfides (LIPs) and the lithium dendrites in Li-S batteries, the separator modified by hollow carbon material was prepared by the simple scraping method. It can be found from the contact angle tests that the layers formed by the porous carbon of uniform width exhibited both stronger attractions to LIPs and better permeability of electrolytes than the bare polypropylene (PP) separator. Permeation tests further showed an effective block over LIPs by the modification layers. Cathode symmetrical batteries with Celgard 3501 separator were assembled and the current response tests implied a conversion of LIPs to Li2S catalyzed by hollow carbon materials. Lithium symmetrical batteries with modified separators were assembled and the voltage-time profile of charge-discharge processes showed better stability owing to the prevention of lithium dendrites. The Li-S batteries were assembled with sulfur loading of 1.8-2.0 mg.cm(-2) and with the bare PP, single-side modified, and double-side modified separators. Calculations of the diffusion coefficient of lithium-ion from galvanostatic intermittent titration technique (GITT) tests and Nyquist plots both indicated the faster ion transportation for the modified separators. Smaller semicircles for impedance were also found in the plots. Nyquist plots after the 1st, 5th, 10th, 50th, and 100th cycles were analyzed to show a stable diffusion behavior of lithium ions, which should be caused by the multichannel from hollow carbon material to provide more paths for Li+ ion transportation. Li-S batteries with double-side modified separators presented a high specific capacity of 1 035 mAh.g(-1) in the first cycle and 500 mAh.g(-1) after 700 cycles at the current density of 0.2C, 630 mAh.g(-1) after 100 cycles at 1C, and 505 mAh.g(-1) after 100 cycles at 2C. The rate performance also behaved superior to the cells with bare PP as the separator. The cell assembled with higher sulfur content (3.2 mg.cm(-2)) also presented the reverse specific capacity of 500 mAh.g(-1) at 0.2C. These battery performances could be ascribed to the porous hollow carbon materials for their adsorption and conversion of LIPs and their prevention of dendrites. Thus, the physicochemical interaction between hollow carbon and LIPs effectively alleviates the shuttle effect and the bifunctional modification of the separator could prevent the growth of lithium dendrites to improve the safety of the Li-S batteries.

A film coating assembled by tubular nitrogen-doped carbon fibers as an efficient membrane spacer to suppress the shuttle effect for long-life lithium–sulfur batteries

Fabrication of electrospun bilayer separators for lithium-sulfur batteries: A surface and structure dual modification strategy

Tg-C 3 N 4 -coated functional separator as polysulfide barrier of high-performance lithium-sulfur batteries

A three-dimensional interconnected nitrogen-doped graphene-like porous carbon-modified separator for high-performance Li-S batteries

Multifunctional Lithium Phytate/Carbon Nanotube Double-Layer-Modified Separators for High-Performance Lithium-Sulfur Batteries

Cellulose nanofiber separator for suppressing shuttle effect and Li dendrite formation in lithium-sulfur batteries

NiFe2O4/Ketjen Black Composites as Efficient Membrane Separators to Suppress the Shuttle Effect for Long-Life Lithium-Sulfur Batteries

Synergistic inhibitory effect of ultralight CNTs-COOH@Fe3O4 modified separator on polysulfides shuttling for high-performance lithium–sulfur batteries

A Polar TiO/MWCNT Coating on a Separator Significantly Suppress the Shuttle Effect in a Lithium-Sulfur Battery

A Lithium‐Affinitive Covalent Organic Polymer Network Functionalized Separator for Dendrite‐Free and High‐Durability Lithium–Sulfur Batteries under Harsh Conditions

Empowering polypropylene separator with enhanced polysulfide adsorption and reutilization ability for high-performance Li-S batteries

Designing a Functional CNT+PB@MXene-Coated Separator for High-Capacity and Long-Life Lithium-Sulfur Batteries

A carbon mixed selenium sulfide separator coating for lithium‐sulfur battery life enhancement

A thin multifunctional coating on a separator improves the cyclability and safety of lithium sulfur batteries.

A multifunctional separator modified with cobalt and nitrogen co-doped porous carbon nanofibers for Li–S batteries

NC-Co3O4 Polyhedron Embedded Multifunctional Separator Based on Structural Engineering Towards Stable and Durable Lithium-Sulfur Battery

CoP/C Nanocubes-Modified Separator Suppressing Polysulfide Dissolution for High-Rate and Stable Lithium-Sulfur Batteries.

Glass Fiber Separator Coated by Porous Carbon Nanofiber Derived from Immiscible PAN/PMMA for High-Performance Lithium-Sulfur Batteries

A dual-coated multifunctional separator for the high-performance lithium-sulfur batteries

Application of Double-Side Modified Separator with Hollow Carbon Material in High-Performance Li-S Battery

Ultrafine Co-Species Interspersed g-C3N4 Nanosheets and Graphene as an Efficient Polysulfide Barrier to Enable High Performance Li-S Batteries