Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Dual Optimization of Bulk and Surface via Guanidine Halide for Efficient and Stable 2D/3D Hybrid Perovskite Solar Cells

Above 23% Efficiency by Binary Surface Passivation of Perovskite Solar Cells using Guanidinium and Octylammonium Spacer Cations

An Effective Strategy of Combining Surface Passivation and Secondary Grain Growth for Highly Efficient and Stable Perovskite Solar Cells

Efficient and Stable 2D@3D/2D Perovskite Solar Cells Based on Dual Optimization of Grain Boundary and Interface

Double‐Sided Surface Passivation of 3D Perovskite Film for High‐Efficiency Mixed‐Dimensional Perovskite Solar Cells

Simultaneous Passivation of Bulk and Interface Defects with Gradient 2D/3D Heterojunction Engineering for Efficient and Stable Perovskite Solar Cells.

Additive Engineering by Bifunctional Guanidine Sulfamate for Highly Efficient and Stable Perovskites Solar Cells

Synergistic Full‐Scale Defect Passivation Enables High‐Efficiency and Stable Perovskite Solar Cells

Surface Passivation Using 2D Perovskites toward Efficient and Stable Perovskite Solar Cells

Buried Guanidinium Passivator with Favorable Binding Energy for Perovskite Solar Cells

Surface Terminated 3D/2D Heterojunction Enables Efficient and Stable Perovskite Solar Cells

Dual Optimization of Bulk and Interface Via the Synergistic Effect of Ligand Anchoring and Hole Transport Dopant Enables 23.28% Efficiency Inverted Perovskite Solar Cells

Stable High‐Efficiency CsPbI2Br Solar Cells by Designed Passivation Using Multifunctional 2D Perovskite

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Impeded Degradation of Perovskite Solar Cells Via the Dual Interfacial Modification of Siloxane

Interface and Bulk Engineering by Dual Sulfonates Toward High Efficiency Perovskite Solar Cells with Better Reproducibility and Stability

Multi‐Functional Interface Passivation via Guanidinium Iodide Enables Efficient Perovskite Solar Cells

Sodium Dodecylbenzene Sulfonate Interface Modification of Methylammonium Lead Iodide for Surface Passivation of Perovskite Solar Cells

Magnetic Field‐Assisted Interface Embedding Strategy to Construct 2D/3D Composite Structure for Stable Perovskite Solar Cells with Efficiency Over 24%

In Situ Dual‐Interface Passivation Strategy Enables The Efficiency of Formamidinium Perovskite Solar Cells Over 25%