Abstract:This study investigates the metallurgical and mechanical properties of a nickel-based superalloy produced through wire + arc additive manufacturing (WAAM). It is a novel and fast fabrication technique based on layer-by-layer construction for rapid product development. A thin-wall component of Inconel 625 was successfully manufactured using a cold metal transfer (CMT)-based WAAM technique with an ErNiCrMo-3 wire after identifying suitable process parameters based on trial runs. The microstructure varies based on the travel and build directions, resulting in columnar, cellular, and equiaxed dendrites found in bottom, middle, and top regions. These dendritic structures evolve throughout the deposition process, predominantly influenced by temperature circumstances. The results of SEM/EDS analysis indicated that Nb and Mo segregation was lower in the interdendritic areas compared to the dendritic core areas of the thin-wall part. The XRD results discovered that the main crystal structure found in the WAAMed samples was a γ-FCC (face-centered cubic). Additionally, through EBSD analysis, the average grain size was identified as 86.45 μm in the travel direction and 89.15 μm in the build direction. The grain properties of the material were influenced by the reheating phenomenon and the circumstances of solidification that occurred throughout the layer-by-layer additive manufacturing process. The larger proportion of higher angle grain boundaries improves the mechanical properties. The average hardness in the travel direction was higher in the top (312 HV), middle (297 HV), and bottom (303 HV) sections than in the build direction (305 HV), (290 HV) and (294 HV), respectively. The mechanical properties, specifically tensile strength, exhibit anisotropy that varies depending on the direction of travel and build. The residual stress analysis shows that the as-built specimen is mainly affected by tensile stress in the travel and build directions.

A performance comparison of additive manufactured creep-resistant superalloys

High temperature performance of wire-arc additive manufactured Inconel 718

Achieving superior elevated temperature properties in additive manufactured nickel-based superalloys through unique alloy design

Achieving High Strength and Creep Resistance in Inconel 740H Superalloy through Wire-Arc Additive Manufacturing and Thermodynamic-Guided Heat Treatment

Metallurgical Evaluation of an Additively Manufactured Nickel-Base Superalloy for Gas Turbine Guide Vanes

Recrystallization behavior and mechanical properties of Haynes 282 fabricated by wire-arc additive manufacturing with post-heat treatment

Creep Behavior and Deformation Mechanism of a Third-Generation Single Crystal Ni-Based Superalloy at 980 °C

In Situ SEM Study of Creep Deformation Behavior of Nickel-Based Single-Crystal Superalloys

Influence of Replacing Molybdenum with Tungsten on the Creep Fracture Property of Waspaloy Nickel-Based Alloy

High-temperature mechanical properties of nickel-based superalloys manufactured by additive manufacturing

A Study on Microstructure and Mechanical Properties of Inconel 718 Superalloy Fabricated by Novel CMT-WAAM Process

Towards Superior High Temperature Properties in Low Density AlCrFeNiTi Compositionally Complex Alloys

Influences of a Hot-Working Process on the Microstructural Evolution and Creep Performance of a Spray-Formed Nickel-Based Superalloy

Small punch creep test reveals the differences of high-temperature creep behaviours for laser powder bed fusion and Rolled Inconel 718 alloys

Alloy Design and Development of High Cr Containing FeCrAl Ferritic Alloys for Extreme Environments

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

The creep deformation of a new nickel-base alloy-by-design studied using synchrotron X-ray diffraction

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

Long-Term Creep Behavior of a CoCrFeNiMn High-Entropy Alloy

Microstructure Impacts on Mechanical Properties in a High Temperature Austenitic Stainless Steel