Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. The current research addresses the challenges encountered in polyamide 6 carbon fiber composites synthesized by fused deposition modeling. It specifically investigates issues such as inadequate interlaminar bonding and increased void content compared to conventionally manufactured composite components and as-built printed parts. The study focuses on printing pin samples via fused deposition modeling and explores various thermal post-processing methods to reduce void content while preserving dimensional accuracy. To evaluate wear and friction behavior, a pin-on-disc tester was used to test both as-built samples and samples post-heat-treated at 70 °C, 140 °C, and 210 °C. The results indicate that as the applied load increases from 5 to 20 N, both wear rates and friction coefficients increase across all speeds (1–5 m/s). Heating the samples to 70 °C and 140 °C strengthens the interlayer bonding. This significantly improves the maximum wear rates and friction coefficients compared to the as-built samples. However, samples heated to 210 °C do not show much of a change in wear rates or friction coefficients. Samples heated to 210 °C exhibit a decrease in wear rate of 16.87%, 15.82%, and 15.73% for loads ranging from 5 to 20 N, at speeds of 1, 3, and 5 m/s, respectively. This is likely due to pores sealing off and structures binding tightly. The worn surfaces were analyzed using a scanning electron microscope and measured the Shore D hardness of the samples before and after wear testing and documented the results for further analysis. In a scanning electron microscope, samples treated at 210 °C displayed smoother, less worn surfaces. Shore D hardness tests revealed a slightly higher hardness in samples heated to higher temperatures, followed by higher loads and sliding speeds in tribometer tests. This showed that the material was more stable. These post-processing methods significantly advance the development of functional composite elements for superior structural or dynamic performance.

Viscoelastic and heat-resistant behavior of surface-treated areca fruit husk fiber-reinforced polymer composites

Mechanical, morphological and wear resistance of natural fiber / glass fiber-based polymer composites

Insight to the influence of alkali treatment on mechanical and tribological properties of a novel carbon/jute hybrid porcine filled polyester composite

Influence of optimal alkali treated Areca catechu L. peduncle fiber for light weight polymer composites applications

Development And Characterization Of Alkali Treated Abaca Fiber Reinforced Friction Composites

Effect of Aramid Pulp and Lapinas Fiber on the Friction and Wear Behavior of NBR Powder–Modified Phenolic Resin Composite

Sustainable Development of Agro-Industrial Waste-Based Banana Fiber/Fly Ash Polyester Composites for Wear and Friction Study

Investigation on the physical, mechanical and tribological properties of areca sheath fibers for brake pad applications

Enhancement of tribology behaviour by the addition of different fiber length of pineapple fiber reinforced polyester composite

Incorporating date palm fibers for sustainable friction composites in vehicle brakes

The Improvement of the Tribological Behaviour of Chemically Treated Abaca Fibre-Reinforced Polymer Composites

Influence of Load and Sliding Velocity on Abrasive Wear of Polyester Composites Reinforced with Bio-Particulates as Filler Material

Exploration of Mechanical Attributes, Thermal Behaviors and Atomic Force Analysis of Alkali Treated Hybrid Polyester Composites for an Engineering Application

An investigation on tribology performance of Abutilon Indicum fibre reinforced polymer composites

Tribological Behaviour of Short Carbon Fiber Reinforced Polyethersulfone Composites with PTW Filler

Evaluating the impact of post-processing on the wear and friction properties of polyamide 6 carbon fiber composites produced by fused deposition modeling

Effects of sisal fiber and fly ash on the mechanical and tribological performances of brake friction composites

Performance assessment of agricultural waste based eco‐friendly brake friction composites

Repercussion of Fiber Content on the Mechanical, Thermal, and Thermomechanical Properties of Natural Fibers Reinforced Thermoplastic Composites for Automotive Application

Influence of banana fiber on physicomechanical and tribological properties of phenolic based friction composites

Optimization and modelling of the fracture inhibition potential of heat treated doum palm nut fibres in phenolic resin matrix polymer composite: a Taguchi approach