Abstract:SnO2 has the advantages of excellent photostability and can be prepared at low-temperature below 200 degrees C.It is regarded as one of the excellent materials for the electron transport layer, and widely used in efficient andstable planar heterojunction perovskite solar cells. In this work, the low-cost, dense and uniform SnO2 electrontransport layer is prepared by spin coating at low temperature (150 degrees C) for perovskite solar cells with astructure of FTO/SnO2/CH3NH3PbI3 (MAPbI3)/Spiro-OMeTAD/Au. The crystallization and photoelectricproperties of SnO2 electron transport layers prepared at different concentrations (2.5%-10%) at 150 degrees C, and theinfluences of SnO2 electron transport layers on the formation of perovskite films and the performances ofperovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visiblelight absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverageand light transmittance of the substrate and band gap of the SnO2 film increase as the SnO2 content increases,while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-statephotoluminescence spectrum (PL) analysis of the SnO2/MAPbI3 thin film, it is found that the MAPbI3deposited on the SnO2 layer with a concentration of 7.5% is uniform and pinhole-free, has the largest particlesize and the best crystallinity, as well as more effective charge extraction capability and transport capability.By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, theSnO2 electron transport layer with a concentration of 7.5% has better interface contact and lower interfaceresistance, which is beneficial to reducing the recombination of carriers and improving the photoelectricconversion capability, The perovskite solar cells based on SnO2 layer prepared with a concentration of 7.5%reaches a photoelectric conversion efficiency of 15.82% (Voc = 1.06 V, Jsc = 21.62 mA/cm2, FF = 69.40%), Afterstoring for 600 h in ambient air ((25 +/- 5) degrees C, RH>70%) without encapsulation, its efficiency remains 92% of theinitial efficiency. At the same time, we prepare flexible devices on flexible substrates (TIO/PEN) by using SnO2precursor with a concentration of 7.5%, which exhibits good photovoltaic performance and achieves aphotoelectric conversion efficiency of 13.12%, and storage time for 84 d in ambient air ((30 +/- 5) degrees C, RH>70%)without encapsulation, its efficiency remains 48% of the initial efficiency. The PCE retains 78% of the initialefficiency after 1000 bending cycles with a bending radius of 3 mm. The study of optimizing the concentrationof SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Low‐Temperature Processing Methods for Tin Oxide as Electron Transporting Layer in Scalable Perovskite Solar Cells

Ultralow‐temperatureSnO2 Electron Transport Layers Fabricated by Intermediate‐controlled Chemical Bath Deposition for Highly Efficient Perovskite Solar Cells

Low-temperature Preparation of Tin Dioxide Electron Transport Layer in Perovskite Solar Cells

A Compact Electron Transport Layer Using a Heated Tin‐Oxide Colloidal Solution for Efficient Perovskite Solar Cells

Millisecond-pulsed Photonically-Annealed Tin Oxide Electron Transport Layers for Efficient Perovskite Solar Cells

Tin Oxide Electron‐Selective Layers for Efficient, Stable, and Scalable Perovskite Solar Cells

A Low‐Temperature, Solution Processable Tin Oxide Electron‐Transporting Layer Prepared by the Dual‐Fuel Combustion Method for Efficient Perovskite Solar Cells

Ionic liquid modified SnO2 nanocrystals as a robust electron transporting layer for efficient planar perovskite solar cells

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

Recent Advances in Metal Oxide Electron Transport Layers for Enhancing the Performance of Perovskite Solar Cells

Highly-Crystalline SnO2 Thin Films for Efficient Planar Perovskite Solar Cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Low-temperature Preparation of SnO<sub>2</sub> Electron Transport Layer for Perovskite Solar Cells

Regulation of SnO2 Electron Transport Layers for Perovskite Solar Cells

Robust Electron Transport Layer of SnO2 for Efficient Perovskite Solar Cells: Recent Advances and Perspectives

Low‐Temperature‐Processed WO X As Electron Transfer Layer for Planar Perovskite Solar Cells Exceeding 20% Efficiency

Reactive-Sputtered Prepared Tin Oxide Thin Film As an Electron Transport Layer for Planar Perovskite Solar Cells

Low-temperature preparation of SnO2 electron transportlayer for perovskite solar cells

Vacuum Thermal-Evaporated SnO2 As Uniform Electron Transport Layer and Novel Management of Perovskite Intermediates for Efficient and Stable Planar Perovskite Solar Cells

Low‐Temperature Solution‐Processed ZnO Electron Transport Layer for Highly Efficient and Stable Planar Perovskite Solar Cells with Efficiency over 20%