Abstract:Patients with a spinal cord injury (SCI) are susceptible to deep tissue injury (DTI), a necrosis in excessively deformed muscle tissue overlying bony prominences, which, in wheelchair users, typically occurs in the gluteus muscles under the ischial tuberosities. Recently, we developed a generic real-time, subject-specific finite element (FE) modeling method to provide monitoring of mechanical conditions in deep tissues deformed between bony prominences and external surfaces. We previously employed this method to study internal tissue loads in plantar tissues of the foot [Yarnitzky, G., Z. Yizhar, and A. Gefen. J. Biomech. 39:2673-2689, 2006] and in muscle flaps of residual limbs in patients who underwent transtibial amputation (Portnoy, S., G. Yarnitzky, Z. Yizhar, A. Kristal, U. Oppenheim, I. Siev-Ner, and A. Gefen. Ann. Biomed. Eng. 35:120-135, 2007). The goal of the present study was to adapt the method to study the time-dependent mechanical stresses in glutei of patients with SCI during wheelchair sitting, continuously in real-time, and to compare the trends of internal tissue load data with those of controls. Prior to human studies, the real-time FE model-adapted to study the buttocks during sitting-was validated by comparing its predictions to data from a physical phantom of a buttocks and to non-real-time, commercial FE software. Next, real-time, subject-specific, FE models were built for six participating subjects (3 patients with SCI, 3 controls) based on their individual anatomies from MRI scans. Subjects were asked to sit normally in a wheelchair, on a ROHO cushion, and to watch a 90 min movie. Continuous interface pressure measurements from a pressure mat were used as subject-specific boundary conditions for real-time FE analyses of deep muscle stresses. Highest peaks of compression, shear and von Mises stresses throughout the trial period, and averages of peaks of these stresses were recorded over the trial for each individual. These parameters generally had 3-times to 5-times greater values in patients with SCI compared with controls. Likewise, stress doses, defined as the integration of peak compression stress over time, were approximately 35-times and approximately 50-times greater in the subjects with SCI, the values referring to the highest of all peaks recorded throughout the trial, and to average of peaks over the trial, respectively. We believe that by allowing-for the first time-practical and continuous monitoring of internal tissue loads in patients with motosensory deficits, without any risk or interruption to their lifestyle, and either at the clinical setting or at home, the present method can make a substantial contribution to the prevention of severe pressure ulcers and DTI.

Smart Cushions with Machine Learning-Enhanced Force Sensors for Pressure Injury Risk Assessment

Evaluating Head Impact Intensities and Accelerations Using Flexible Wearable Sensors for Traumatic Brain Injury Assessment

Smart seat cushion feasibility pilot study: automated interface pressure modulation of individuals with spinal cord Injury

A Preliminary Study of Smart Seat Cushion Design

Posture Detection Based on Smart Cushion for Wheelchair Users

A Privacy-Preserving and Unobtrusive Sitting Posture Recognition System Via Pressure Array Sensor and Infrared Array Sensor for Office Workers

Development of low-cost pressure mapping device to evaluate force distribution for seat cushion modification

Real-time finite element monitoring of sub-dermal tissue stresses in individuals with spinal cord injury: toward prevention of pressure ulcers

A deep learning based 2-dimensional hip pressure signals analysis method for sitting posture recognition

Automated Patient Handling Activity Recognition for At-Risk Caregivers Using an Unobtrusive Wearable Sensor

Smart Clothing with Built‐In Soft Sensing Network for Measuring Temporal and Spatial Distribution of Pressure under Impact Scenarios

Sensing from the Bottom: Smart Insole Enabled Patient Handling Activity Recognition Through Manifold Learning

Patient Handling Activity Recognition Through Pressure-Map Manifold Learning Using a Footwear Sensor

Bone Geometry on the Contact Stress in the Shoulder for Evaluation of Pressure Ulcers: Finite Element Modeling and Experimental Validation.

Toward Unobtrusive Patient Handling Activity Recognition for Injury Reduction among At-Risk Caregivers

Posture Prediction for Healthy Sitting using a Smart Chair

Preventing postoperative moderate- and high-risk pressure injuries with artificial intelligence-powered smart decompression mattress on in middle-aged and elderly patients: a retrospective cohort analysis

Wireless, multimodal sensors for continuous measurement of pressure, temperature, and hydration of patients in wheelchair

Smart Monitoring Pad for Prediction of Pressure Ulcers with an Automatically Activated Integrated Electro-Therapy System

Intelligent Posture Training: Machine-Learning-Powered Human Sitting Posture Recognition Based on a Pressure-Sensing IoT Cushion

Smart Mat Used for Prevention of Hospital-Acquired Pressure Injuries