Abstract:This paper reports an analysis of the process of heating a graphitized hollow electrode (GHE) during steel processing in ladle-furnace. The results of the numerical modeling of electrode operation are given. The data on the temperature field of the electrode were obtained when electricity was supplied and during periods without electrical loading. Values of the Joule heat released at electrode operation during the periods of metal heating in ladle-furnace were calculated; they amounted to 1.11–1.15 MW/m3. Coefficients of the heat transfer by convection have been calculated for the inner and outer GHE surface: 1.60 and 1.80, and 5–17 W/(m2∙°C), respectively. Values of the electrode temperature gradient in the high-temperature zone were obtained, which, for the first heating period, reached 8,286 °C/m, for the third ‒ to 6,571 °C/m. It was established that during the cooling periods of the electrode, the temperature gradient is significantly reduced and amounts to the inner surface of 379 °C/m; to the outer surface ‒ 3,613 °C/m; the vertical plane to the end of the electrode ‒ 1,469 °C/m. The directions to improve the installation’s thermal work and reduce its resource intensity during out-of-furnace processing of steel have been defined. It has been determined that during the periods of electrode operation with current supply, significant values of the temperature gradient are observed, which are concentrated in the end part. During the periods of operation without current supply, a locally overheated zone forms, taking the shape of a torus flattened along the axis, which is created as a result of the accumulation of heat from the preceding period. The data have been acquired on the effect exerted by the gas supply through a hollow electrode on the parameters of formation of the high-temperature GHE regions. It has been shown that the supply of neutral gas through a graphitized hollow electrode at a flow rate of 0.05 m3/min shifts the high-temperature zone to the periphery by 3.5–4.2 mm, as well as reduces its height by 1.0–1.2 mm. The study reported here could make it possible to calculate expedient gas and material consumption for controlling the oxidation of metal and slag, to reduce the consumption of graphitized electrodes, to bring down energy- and resource costs for metal production

Investigation of the waste heat recovery and pollutant emission reduction potential in graphitization furnace

Numerical Study on the Heat Recovery and Cooling Effect by Built-in Pipes in a Graphitization Furnace

Experimental Investigation on the Thermal Performance of Cooling Pipes Embedded in a Graphitization Furnace

On-Site Experimental Study on Low-Temperature Deep Waste Heat Recovery of Actual Flue Gas from the Reformer of Hydrogen Production

NOxremoval Coupled with Energy Recovery in Sintering Plant

Utilizing flue gas low-grade waste heat and furnace excess heat to produce syngas and sulfuric acid recovery in coal-fired power plant

Electric-Thermal Analysis of Power Supply Module in Graphitization Furnace

Modeling, thermodynamic and techno-economic analysis of coke production process with waste heat recovery

Design on a Novel Waste Heat Recovery System Integrated with the Bypass Flue and Outside Primary Air Preheater for Bitumite-Fired Power Plants

Experience of using evaporative cooling of graphitized electrodes to reduce their consumption in ore smelting furnaces

Influence of carbon material on the production process of different electric arc furnaces

EFFICIENCY OF USING EVAPORATIVE COOLING TO REDUCE THE CONSUMPTION OF GRAPHITE ELECTRODES IN ARC FURNACES OF LOW CAPACITY

Integration of coal gasification and waste heat recovery from high temperature steel slags: an emerging strategy to emission reduction

Numerical and experimental investigations of converter gas improvement inside a flue using its waste heat and CO2 by pulverized coal injection

A novel method of combined desulfurization and heat utilization of low-temperature flue gas from hot blast stove for blast furnace: Laboratory research and industrial application

The Study on the Purification of Waste Graphite Thermal Field Material of FZ-Si Crystal

Analysis of energy, exergy and CO 2 emissions in a fiberglass furnace with oxy-fuel combustion

Carbon Cycle in A Steelmaking Mill: Recycling of Kish Graphite and Its Subsequent Application for Steelmaking Carburant

Performance study and application of new coal-fired boiler flue gas heat recovery system

Intelligent Optimization and Impact Analysis of Energy Efficiency and Carbon Reduction in the High-Temperature Sintered Ore Production Process

Determining changes in the temperature field of a graphitized hollow electrode during metal processing periods in ladle-furnace