Abstract:Superwettability can affect the performance of oil separation from water during the treatment of oily wastewater. Among various types of materials developed for cleaning oil pollution, foam is a popular choice due to its attractive lightweight properties and adjustable porosities. Foams with superwetting surfaces (superhydrophilic/superoleophobic underwater) are ideal for oil/water separations. In this study, lignin-based polyurethane foams (LPUFs) were synthesized first, and then polydopamine particles were deposited on the surface of the foam by in situ polymerization under weak alkaline conditions to increase its surface roughness. Afterwards, phytic acid was used to modify the foam to achieve surface superhydrophilicity and underwater superoleophobicity. Successful loading of polydopamine (PDA) particles and coating of phytic acid (PA) onto the foam was demonstrated by SEM, EDS, FTIR, XPS, and thermogravimetric analysis measurements. It was shown in the cyclic compression tests that LPUFs had good mechanical properties. Under 75 % compression strain, the maximum stress in the first cycle of LPUF/PDA/PA was 105.92 kPa. After 30 cyclic compression tests, the maximum stress of LPUF/PDA/PA under 75 % compression strain was 105.63 kPa, demonstrating a high mechanical stability. The contact angle of the foam modified by PDA and PA was 0° for water, 166.7° for chloroform, and 158.4° for hexane, which also demonstrated excellent underwater anti-oil adhesion performances. Oil-water separation tests by using PDA and PA modified lignin-based foam with mixtures of water and n -hexane, cyclohexane, toluene, and pump oil indicated a separation efficiency of over 99 % for the types of mixtures tested together with excellent repeatability. In addition, the PDA and PA modified lignin-based foams were able to adsorb 67.1 mg/g of methylene blue, 96.1 mg/g of rhodamine B, and 98.2 mg/g of copper sulfate. The lignin-based foam could completely degrade under weak alkaline conditions after usage. This study highlighted a novel strategy for synthesizing environmentally friendly high-performance adsorbents to efficiently treat polluted wastewater using lignin as a raw material.

Bottom-up and up-down strategy to obtain the highly porous polystyrene foam for oily water remediation

Hierarchically porous superhydrophobic sponge for oil-water separation

Mussel-Inspired and In Situ Polymerization-Modified Commercial Sponge for Efficient Crude Oil and Organic Solvent Adsorption

Facile Fabrication of Hydrophobic Porous Monoliths from Charge-Driven Assembled Polymers-Stabilized High Internal Phase Emulsion for Oil Spills Reclamation

Thermally stable and superhydrophobic foam prepared by high‐internal phase emulsion for oil/water separation with good recycling capacity

Rapid and efficient oil removal from O/W emulsions by hydrophobic porous polystyrene microspheres embedded with hydrophilic surface micro-regions

Superhydrophobic/ superoleophilic polystyrene-based porous material with superelasticity for highly efficient and continuous oil/water separation in harsh environments

Superhydrophobic nanoporous polymer-modified sponge for in situ oil/water separation

A scalable versatile methodology to construct micro/nano open-cell polypropylene foam with high oil adsorption capacity and speed

Design of Recyclable Superhydrophobic PU@Fe3O4@PS Sponge for Removing Oily Contaminants from Water

pH-responsive smart superwetting Fe foam for efficient in situ on-demand oil/water separation

Multifunctional superhydrophilic/underwater superoleophobic lignin-based polyurethane foam for highly efficient oil-water separation and water purification

Environment-Friendly Superhydrophobic Sponge for Highly Efficient Oil/Water Separation and Microplastic Removal

Facile fabrication of expanded graphite/polydimethylsiloxane foams for oil–water separation

Three-dimensional structured sponge with high oil wettability for the clean-up of oil contaminations and separation of oil–water mixtures

One-step preparation of durable pH-responsive polyurethane foam for oil/water separation

Hydrophobic and oleophilic open-cell foams from in-situ microfibrillation blends of poly(lactic acid) and polytetrafluoroethylene: Selective oil-adsorption behaviors

A Facile Method to Fabricate Superoleophilic and Hydrophobic Polyurethane Foam for Oil–water Separation

Highly efficient oil-water separation and oil adsorption with hydrophobic hydrotalcite/polyurethane porous composite foam

Multifunctional hydrophobic bio-based foam toward highly efficient photothermal cleanup of high-viscosity crude oil spills, oil-water separation and aqueous organic pollutant elimination

Preparation of a porous superhydrophobic foam from waste plastic and its application for oil spill cleanup