Abstract:Nanocellulose extracted from lignocellulosic biomass not only provides a promising way to deal with lignocellulosic biomass wastes but also contributes to the performance of cementitious materials. In this study, sulfated cellulose nanocrystals (CNCs) were selected as nanoreinforcement for cement mortars to improve their mechanical properties, especially the flexural strength. Three different sonication procedures were applied to CNC suspensions with CNC dosages of 0.01%, 0.05%, and 0.1% to improve their dispersion. The sonicated suspensions then were incorporated into the mortars. The effects of the sonication procedure and the CNC dosage on the particle dispersion of CNC suspension and the mechanical properties of mortars were examined in detail. The result showed that increasing the sonication energy from ∼7,835 to ∼37,587 J or lowering the CNC dosage from 0.1% to 0.01% could eliminate the aggregation of CNCs and increase the magnitude of the zeta potential of the CNC suspension, resulting in better dispersion (less aggregation in water). When continuous sonication for 12 min was used, the flexural strength of mortars with 0.01% CNC dosage improved the most, about 10%; however, an unexpectedly obvious decrease occurred when the CNC dosage was increased to 0.05% or 0.1%, which was due mainly to the reduced cement hydration degree and the more porous microstructure of the mortars. Thus, the optimum sonication energy needs to be adjusted for different dosages of CNC used; otherwise the CNC may have a negative effect on the performance of cement mortars. Given the same sonication procedure, the compressive strength of specimens did not change too much with the variation of CNC dosage; however, the flexural strength varied. For 3- and 28-day specimens, the flexural strength had maximum values for 0.05% and 0.01% CNC dosages, respectively. In addition, this study indicated that the improved dispersion of CNCs in water cannot ensure the significant strength improvement of mortars.

Super plasticizer assisted bath ultra sonication for dispersion of multi walled carbon nanotubes in cement composites

Performance Evaluation of MWCNTs Reinforced Cement Mortar Composites using Natural and Commercial Surfactants

Dispersion of Multi-Walled Carbon Nanotubes into White Cement Mortars: The Effect of Concentration and Surfactants

An Effective Method for Hybrid CNT/GNP Dispersion and Its Effects on the Mechanical, Microstructural, Thermal, and Electrical Properties of Multifunctional Cementitious Composites

Development of cement nanocomposites reinforced by carbon nanotube dispersion using superplasticizers

Research on the influence of dispersed carbon nanomaterials with different water reducing agent in cementitious mortar

Ultrasonic and superplasticizer assisted dispersion of hybrid carbon nanomaterials (FCNT and GO): its effect on early stage hydration and physico-mechanical strength of cement mortar

Reinforcement of Cement Nanocomposites through Optimization of Mixing Ratio between Carbon Nanotube and Polymer Dispersing Agent

Optimization of preparation parameters and testing verification of carbon nanotube suspensions used in concrete

Effect of ultrasonication on the properties of multi-walled carbon nanotubes/ hollow glass microspheres/epoxy syntactic foam

Workability and Mechanical Properties of Superplasticized Microfine Cement Grouts

Multi-scale Structure of In-Situ Polymerized Cementitious Composites with Improved Flowability, Strength, Deformability and Anti-Permeability

Compressive Strength and Microstructure of Multi-Wall Carbon Nanotubes Reinforced Cement Composites

Dispersion of Sonicated Sulfated Cellulose Nanocrystals and Their Effect on the Mechanical Properties of Cement Mortars

Surface modification and dispersity of chopped carbon fiber and its effects on mechanical properties of gypsum-based composite materials

Influence of Different Surfactants on Carbon Fiber Dispersion and the Mechanical Performance of Smart Piezoresistive Cementitious Composites

Research on the toughening mechanism of modified nano-silica and silane molecular cages in the multi-scale microfracture of cement-epoxy composite

Carbon Nanotubes in Cement—A New Approach for Building Composites and Its Influence on Environmental Effect of Material

Experimental Testing on Mechanical, Durability, and Adsorption Dispersion Properties of Concrete with Multiwalled Carbon Nanotubes and Silica Fumes

A Novel Approach to Methoxy Polyethylene Glycol-Grafted Sulfonated Poly(maleic Anhydride-Alt-styrene) As Superplasticizers in Cement Pastes

Effectiveness Assessment of Superplasticizer Admixtures: Case of Self-compacting Concrete Reinforced with Fine Mineral Fillers