Abstract:The present study investigates the variations in the microstructure and mechanical properties of AA2024 aluminum alloy as a consequence of thermal and strain gradient in combined hot forming cold die quenching (HFQ) and equal channel angular pressing (ECAP) method. Solution-treated AA2024 aluminum alloy was HFQ–ECAPed for five passes of deformation and 3D simulations plus microstructural evolutions, and mechanical properties over the thickness of the sample were investigated. Furthermore, after each ECAP pass, intermediate solution treatment was applied, and a group of specimens was subjected to aging treatment following the deformation. 3D simulations illustrated strain uniformity by increasing the number of deformation passes with its maximum uniformity after four passes. Microstructural observations demonstrated evident grain refinement in successive passes, which were higher in the central and top parts of the sample than in the lower area. Also, a high quantity of shear bands occurred in the workpiece after the first ECAP pass. However, shear banding was deducted in the consecutive passes of deformation and intermediate solutionizing. Preferable properties in central regions were seen comparing tensile properties in surface area and central parts. Besides, the microhardness test resulted in more uniform outcomes by enhancement in the number of ECAP passes. Hardness variations showed an increase in average hardness after the first pass of deformation (compared to the annealed condition (Baghbani Barenji et al. in J Mater Res Technol 9:1683–1697, 2020) and then a negligible decrease in the following two passes. The hardness quantities again increased in the fourth pass and then dramatically decreased after the fifth pass due to the partial decomposition of the solid solution. Besides, due to strain distribution, hardness values illustrate the maximum and minimum amount in the uppermost and lowermost areas, respectively. The overall conclusions of this article presented mechanical similarities in the surface and inner parts of the material.

Deformation Behavior, Recrystallization Kinetics, Strengthening Mechanisms and Residual Stress in Al-Mg-Si-Ag Alloy Processed by Equal-Channel Angular Pressing

Microstructure and mechanical properties of AlMgSi alloys after equal channel angular pressing at room temperature

Grain Refinement and Strengthening of an Aluminum Alloy Subjected to Severe Plastic Deformation through Equal-Channel Angular Pressing

Superplastic Properties of an Aluminum-Based Alloy after Equal-Channel Angular Pressing

Conjoint influence of equal channel angular pressing and annealing on microstructure and mechanical properties of aluminum alloy 7075Gemeinsamer Einfluss des Gleichkanal‐Winkelpressens und des Glühens auf das Gefüge und die mechanischen Eigenschaften der Aluminiumlegierung EN AW‐AlZn5,5MgCu

A Comparative Analysis of the Stored Energy in Shear-Oriented Grains and Mechanical Properties in Two Al-Mg-Si Alloys Processed by Equal-Channel Angular Processing

Finite Element Simulation and Experimental Investigation of Hot Forming Cold Die Quenching and Equal Channel Angular Pressing of AA2024 Aluminum Alloy

Mechanical Behavior of Processed AZ91D by Equal Channel Angular Extrusion during Semi-Solid Isothermal Compression

Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Overcoming the strength-ductility tradeoff of a 3D-printed Al-Si alloy by equal channel angular pressing

Mechanical Properties and Microstructure of Al–Mg–Mn–Zr Alloy Processed by Equal Channel Angular Pressing at Elevated Temperature

Effect of Preliminary Deformation on the Formation of Ultrafine-Grained Structure during Equal Channel Angular Pressing of Magnesium Alloys

Reducing the Tension–compression Yield Asymmetry of Extruded Mg–Zn–Ca Alloy Via Equal Channel Angular Pressing

Investigation on the Grain Structure Evolution and Abnormal Stress Increase of Al–Mg–Si Alloy During Hot Deformation

Mechanical and microstructural characteristics of AA6082 using thermal equal channel angular pressing for structural applications

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Microstructural evolution of Al-Mg-Er-Zr alloy by equal channel angular extrusion at room temperature

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

Direct Observation of Shear Deformation During Equal Channel Angular Pressing of Pure Aluminum