Abstract:Purpose The purpose of this work is to perform the finite element analysis (FEA) for the numerical discretization of sections with different arrangements of Web openings to investigate the torsion behavior. Typical hexagonal and circular Web opening sections are extensively used in steel construction due to economic development in building design. However, the use of sections with different arrangements of Web opening had improved the performance of the section with Web opening in terms of structural behavior which leads to economic design compared to typical I-beam. Design/methodology/approach The accuracy of FE results allows extensive numerical analysis of stress concentration magnitude for sections with Web openings, concentrating on the sizes and positions of the Web opening. Five shapes and three sizes of Web opening are used in this work. The shapes involved are c-hexagon, hexagon, octagon, circular and square, whereas the sizes of the Web opening involved are 0.67 D, 0.75 D and 0.80 D where D is the height of the Web. Two types of models for 200 × 100 × 8×6 mm steel section involved which is Model 1, where the section with 50 mm edge and 150 mm center-to-center distance and Model 2, where the section with 100 mm edge and 200 mm center-to-center distance. Findings It was found that these configurations affect the section with various shapes of Web openings sizes (0.67 D, 0.75 D, and 0.80 D). This also includes the spacing distances, with 50 mm edge and 150 mm center-to-center distance and also a section with 100 mm edge and 200 mm center-to-center distance. Through the FEA results of Model 1 and Model 2, it is found that 50% reduction in horizontal member length in hexagon Web opening, from 50 mm to 20 mm, caused increment about 30%–53% stress concentration in Web for c-hexagon. However, for a stress analysis of c-hexagon, geometry resulted in a lower stress concentration in the Web than other Web opening. Originality/value Additionally, the work emphasized the efficiency of Web opening shapes by using an appropriate Web opening radius in section with c-hexagon, hexagon, octagon, square and circular shapes. The final results show the contribution of appropriate Web opening radius to increase the section torsional capacity. It is observed that the torsional capacity at certain loading condition and its angle of twist is analysed.

Moment gradient factor for steel I-beams with sinusoidal web openings

Lateral Buckling of Web-Tapered I-beams: A New Theory

Critical Load for Shear-Induced Lateral-Distortional Buckling in I-section Steel Beams Considering Flexural Stiffness Ratio

Elastic Local Buckling and Width-to-Thickness Limits of I-Beams Incorporating Flange–Web Interactions

Flexural-torsional Elastic Buckling of Tapered Beams with Simple Support

Inelastic Storey-Buckling Factor of Steel Frames

Behaviour of Steel I Beams with Web Openings

Experimental and Analytical Investigation of Open Web Steel Beam Under Non-uniform Bending

The numerical assessment of stress distribution of I-beam with web opening

Investigation on Shear Deflection Behaviour of Open Web Steel Beams: An Analytical and Experimental Study

The magnitude of stress concentration of I-beam with web opening because of lateral-torsional buckling effects

Stress analysis of I-beam with web opening via finite element analysis and experimental study

Synthetic SN Curve of Steel Beams with Web Opening

Influence of the web opening shapes on the bending and free vibration responses of castellated steel beams

Research on factors affecting deflection and an approach for evaluating web stress for steel octagon-web beam

Assessment of lateral-torsional buckling capacity of mild steel castellated beam with sinusoidal web openings

Tension-Flange Restraint Effect on Lateral-Torsional Buckling Moment Capacity of Web-Tapered Steel I-Sections

On buckling of compact I-section beams subjected to biaxial bending

Experimental and Finite Element Method of Castellated Steel Beam with and without Hexagonal web opening

Progressive collapse analysis of beam–column substructures considering various reduced beam web sections

Development of efficiency analysis for I-beam steel section with web opening via numerical method