Abstract:Nickel-based alloys have great application value in aerospace, biomedical industry, chemical industry, and other fields. However, nickel-based alloys are known to be difficult to process, which will generate a lot of heat and friction during processing, which limits the application range of nickel-based alloys. Therefore, a large amount of cutting fluid needs to be used during processing, and the cutting fluid will cause harm to human health and the environment. In order to solve these problems, scholars proposed to use the minimum quantity lubrication (MQL) to replace the conventional flood cooling lubrication technique. Recently, many papers have proposed to use MQL for lubrication /cooling in the processing of nickel-based alloys. However, few studies have approached this topic comprehensively. To bridge this gap, this study conducts a comprehensive literature review of the progress made in the processing of nickel-based alloys using various MQL methods. It should be noted that these studies are divided into four categories: vegetable oil-based MQL, cryogenic cooling-based MQL, solid lubricant-based MQL, and electrostatic atomization-based MQL. It is crucial to compare the advantages of these cooling and lubricating technologies in machining nickel-based alloys, analyze their experimental results, and assess their impact on machining quality and tool wear. This review reveals that compared to traditional MQL, vegetable oil-based MQL is more energy-saving and environmentally friendly, resulting in approximately 30% improvement in surface quality and a 50% reduction in tool wear. The addition of solid lubricants to vegetable oil further enhances its lubrication performance. Cryogenic cooling-based MQL enables the attainment of finer grains and smaller sawtooth chips. Electrostatic atomization MQL, by altering the atomization process of traditional MQL, produces more uniform droplets, leading to a 42.4% reduction in tool wear and a 47% improvement in machined surface quality. The purpose of this paper is to help researchers identify existing gaps and to enable MQL to improve the processing quality and application range of nickel-based alloys. Finally, the present technical challenges and future research directions are put forward.

A Review on Machining of Nickel-Based Superalloys Using Nanofluids Under Minimum Quantity Lubrication (NFMQL)

Evaluation of Surface Roughness, Tool Wear and Chip Morphology during Machining of Nickel-Based Alloy under Sustainable Hybrid Nanofluid-MQL Strategy

Minimum quantity lubrication machining nickel base alloy: a comprehensive review

Nanofluids application in machining: a comprehensive review

Non-conventional machining of nickel based superalloys: A review

State-of-the-Art in Sustainable Machining of Different Materials Using Nano Minimum Quality Lubrication (NMQL)

Performance evaluation of nanofluid-based minimum quantity lubrication grinding of Ni-Cr alloy under the influence of CuO nanoparticles

A State-of-the-Art Review on Cutting Tool Materials and Coatings in Enhancing the Tool Performance in Machining the Superior Nickel-Based Superalloys

Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication

Minimum quantity lubrication machining of aeronautical materials using carbon group nanolubricant: From mechanisms to application

A review on minimum quantity lubrication technique application and challenges in grinding process using environment-friendly nanofluids

A Comprehensive Review of Machinability of Difficult-to-Machine Alloys with Advanced Lubricating and Cooling Techniques

Machining response of Ti64 alloy under Nanofluid Minimum Quantity Lubrication (NFMQL)

Investigation on Grindability Improvement of Inconel 625 using Multi-walled Carbon Nanotubes Nanofluids-Assisted Minimum Quantity Lubrication Surface Grinding

A review on cutting tool technology in machining of Ni-based superalloys

Research progress of eco-friendly grinding technology for aviation nickel-based superalloys

Study on High-Speed Machining of 2219 Aluminum Utilizing Nanoparticle-Enhanced Minimum Quantity Lubrication (MQL) Technique

Integrating textured tools and diverse lubricooling approaches in machining performance of Ti and Ni-base alloys – a comprehensive review

Nanoparticle-enhanced coolants in machining: mechanism, application, and prospects

A review on minimum quantity lubrication (MQL) assisted machining processes using mono and hybrid nanofluids

Parametric optimization to establish eco-friendly nanofluid minimum quantity lubrication (NMQL) practice for turning superalloy Inconel 718