Abstract:This study investigates the viability of using plastic oils derived from High-density polyethylene (HDPE), Polypropylene (PP), and Polystyrene (PS) as alternative fuels for diesel engines. The research focuses on comparing the physical and chemical properties, fuel lubricity, engine performance, combustion characteristics, and exhaust emissions of these plastic oils. Analysis revealed that PS exhibits different fuel properties compared to diesel, with a carbon range distribution similar to gasoline, while HDPE and PP properties closely resemble diesel fuel. To prevent potential engine damage, PS was excluded from engine tests. PP displayed the best fuel lubricity, attributed to its higher kinematic viscosity and sulphur content, reducing direct friction. Diesel followed, with PS and HDPE in decreasing order of lubricity. Diesel's lubricity was influenced by the 7% palmitic methyl ester content in the fuel. In engine tests, HDPE demonstrated BTE similar to diesel, while PP exhibited lower BTE due to combustion retardation, leading to increased energy losses and higher BSFC. The combustion characteristics, in-cylinder pressure, and heat release rate of HDPE closely resembled diesel, while PP showed significantly delayed combustion due to low oxygen content and higher kinematic viscosity. Notably, NO X emissions from PP were lower than diesel and HDPE at all engine loads due to heat losses, resulting in a low in-cylinder temperature unsuitable for NO X emission. HDPE produced higher NO X emissions than diesel at low and middle loads due to its higher H/C ratio, promoting high thermal NO X formation. HC emissions from both HDPE and PP were higher than diesel due to increased fuel supply, hindering chemical bond breakdown. Similarly, CO emissions increased for HDPE and PP due to insufficient time for complete combustion, with HDPE producing more CO due to its heavy composites and lower cetane index. Smoke emissions from both HDPE and PP surpassed diesel, attributed to lower oxygen and higher sulphur content, leading to increased sulphurate particulate matter formation, and lower fuel density referring to the high amount of fuel supplied to the engine.

Performance, Combustion and Emission Characteristics of Direct Injection Diesel Engine with Plastic Oil Extracted from Compact Discs

Combustion, performance and emission analysis of a DI diesel engine using plastic pyrolysis oil

Critical insights into the effects of plastic pyrolysis oil on emission and performance characteristics of CI engine

Exergetic performance optimization and thermoeconomic analysis of a variable compression ratio diesel engine fueled with distilled plastic oil and diesel doped with nanographene

The influence of plastic pyrolysis oil on fuel lubricity and diesel engine performance

Extraction and Performance Analysis of Hydrocarbons from Waste Plastic Using the Pyrolysis Process

Waste plastic to pyrolytic oil and its utilization in CI engine: Performance analysis and combustion characteristics

Extraction and characterization of waste plastic pyrolysis oil for diesel engines

Experimental investigation to identify the type of waste plastic pyrolysis oil suitable for conversion to diesel engine fuel

Experimental Investigation in Compression Ratio on Performance, Combustion and Emission of VCR Engine using Pyrolysis-oil Produced from Waste Plastic Materials

Evaluation of Waste Plastic Pyrolysis Oil Performance with Diethyl Ether Additive on Insulated Piston Diesel Engine

Plastic pyrolytic oils as renewable fuel: improving its physical properties and ignition patterns by waste renewable source—an experimental analysis

Effect of camphor oil on a plastic pyrolysis oil fueled DI diesel engine

Experimental investigation of fuel injection timing effects on a CRDI diesel engine running on hydrogen-enriched waste plastic oil

Experimental Evaluation of Performance and Combustion Characteristics of Blended Plastic Pyrolysis Oil in Enhanced Diesel Engine

Processing and utilization of the solid plastic waste oil as the sustainable substitute for fossil fuel for the CI engine from microwave assisted pyrolysis process

The utilisation of oils produced from plastic waste at different pyrolysis temperatures in a DI diesel engine

Investigation on the long-term effects of plastic pyrolysis oil usage in a diesel engine

Study on the Performance and Emissions of Triple Blends of Diesel/Waste Plastic Oil/Vegetable Oil in a Diesel Engine: Advancing Eco-Friendly Solutions

Experimental Analysis of Hydrogen Enrichment in Waste Plastic Oil Blends for Dual-Fuel Common Rail Direct Injection Diesel Engines