Abstract:Combined vibration equipment is widely used in the separation and classification of grain, mineral and other granular materials. The cylindrical slideway on the upper part of the base of the combined vibration equipment bears all the weight of the vibrating silo and the particulate matter in the vibrating silo during the vibration process, and supports the combined vibration of the vibrating silo and the particulate matter in the vibrating silo, the cylindrical slideway on the upper part of the base is seriously worn. The vibrating silo can only vibrate horizontally and linearly along the cylindrical slide on the upper part of the base and swing back and forth around the center of the bottom surface of the cylindrical slide on the upper part of the base. It is required that the cylindrical slide on the upper part of the base has good strength and toughness, and the contact surface has a hardness of more than 35HRC to ensure wear resistance. The effect of laser surface quenching process on the surface hardness of the upper cylindrical slide of the base is studied by using the method of three factors and four levels. The experimental results show that after laser surface quenching, the minimum surface hardness and the maximum surface hardness of the upper cylindrical slide of the base are 35.6HRC and 39.6HRC, which meet the hardness requirements of vibration equipment for the slide of the base. When 1450W laser quenching power, 500mm/min laser scanning speed and 2.25mm laser spot diameter are used, the maximum surface hardness will be 39.6HRC, which is about 38.6% higher than that of the pretreated sample. The maximum section hardness of test sample 14 after laser quenching reaches 388HV, which is about 1.25 times higher than that of the matrix in the quenching areas of samples 13, 15 and 16. It is close to the matrix hardness when it is 1.6mm away from the surface. The thickness of the surface hardened layer exceeds 0.6mm, indicating that the greater the laser power, the greater the thickness of the hardened layer. In the wear test, the minimum wear amount of sample 14 is 0.0331g, which is about 25.2% of the matrix wear amount of 0.1312g. The larger the laser power is, the smaller the scanning speed and spot diameter are, which plays a positive role in promoting the reduction of sample wear. We will use the laser surface quenching process parameters of sample 14: laser power 1450W, spot diameter 2.25mm and scanning speed 500mm/min to conduct laser quenching on the upper cylindrical slide surface of the base of the combined vibration equipment in order to obtain a thicker hardened layer and higher hardness, and greatly improve the service life, safety and stability of the combined vibration equipment.

Effect of laser quenching process on surface hardness and wear performance of cylindrical slideway on the upper base of combined vibration separation equipment

Research on 40Cr Laser Quenching Process for Guide Rail

Effect of laser quenching on wear and damage of heavy-haul wheel/rail materials

Surface characteristic and wear resistance of QT-700-2 nodular cast iron after laser quenching combing with shot peening treatment

Study on the quenching depth and surface hardness of metal materials by laser quenching variable parameters

Microstructure refinement and properties of 1.0C-1.5Cr steel in a duplex treatment combining double quenching and laser surface quenching

Effect of Deep Cryogenic Treatment on Microstructure and Wear Resistance of LC3530 Fe-Based Laser Cladding Coating

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

Experimental Study on the Wear Properties of 42CrMo Steel with Different Microstructures and T15 Laser Cladding

Combining Ultrafast Laser Texturing and Laser Hardening to Enhance Surface Durability by Improving Hardness and Wear Performance

Improving the Properties of Gray Cast Iron by Laser Surface Modification

Comparison on the microstructure, bending properties and tribological behaviors of rail materials treated by laser dispersed quenching and induction assisted laser dispersed quenching

Research on tool wear and surface quality in laser-assisted ultrasonic elliptical vibration cutting of cemented carbide

Investigation on the Microstructure and Damage Characteristics of Wheel and Rail Materials Subject to Laser Dispersed Quenching

Study on laser surface hardening process of 30CrMnSiNi2A ultra-high strength steel fabricated by laser deposition manufacturing

Study on the effects of laser quenching power and scanning speed on the property of cast iron

Improving the surface integrity of laser cladded layer by ultrasonic-assisted burnishing at medium temperature with considering initial surface conditions

Laser Melting and Surface Texture Technology: Effect on Friction Properties

Research on laser quenching process of 20CrMnMo gears by finite element method and experiment

Eddy Current Mapping Technology for Residual Stress and Surface Hardness Evaluation in Laser Hardened Steels

Surface condition driven fatigue performance of laser powder bed fusion H13 steel