Abstract:The use of lime as a binder in hemp–lime considerably increases the drying time of hemp–lime after casting. Furthermore, lime is a non-renewable mineral resource. As such, this paper explores the effectiveness of using an alternative non-mineral binder instead of lime to formulate a novel hemp–shive insulation. The moisture-dependent thermal conductivity, adsorption isotherm, vapour diffusion resistance factor, and in-built hygrothermal performance of four variants of a novel bio-based insulation were investigated. The hygrothermal performance of the novel hemp–shive insulation was compared with that of a previously developed novel hemp–lime insulation. No significant variation in thermal conductivity of hemp–shive insulations between the equilibrium moisture contents (EMC) at 0% and 50% relative humidity (RH) was observed, but there was a substantial increase in thermal conductivity hemp–shive insulations when the material reached the EMC at 98% RH. The average dry thermal conductivity values of hemp–shive and hemp–lime insulations were also similar. The adsorption isotherms of hemp–shive insulations were determined at 0%, 20%, 50%, 70%, 90%, and 98% relative humidity steps. At 98% RH, the moisture adsorption capacity of hemp–shive insulations was 4-to-5-times higher than that of hemp–lime insulation. Hemp–shive insulations' vapour diffusion resistance factor (μ value) was about double the μ value of hemp–lime insulation. Hemp–shive insulations exhibited 4-to-5-times higher water absorption resistance than that of hemp–lime insulation. Numerically determined porosity values of hemp–shive agree with the values of wood-based insulation materials of similar density. Finally, using all experimentally acquired data as inputs, dynamic whole-building hygrothermal simulations were carried out and the results show that novel hemp–shive insulation materials perform at a similar level to the hemp–lime insulation in terms of heating and cooling energy demand but require 45% less energy for humidification. However, the relative humidity inside the hemp–shive wall remains higher than 70%, which can potentially induce mould growth.

Analysis of the Thermal Conductivity of a Bio-Based Composite Made of Hemp Shives and a Magnesium Binder

Research of the physical properties of bio-based building materials with phase change material

Experimental investigation of heat transfer in bio-based building block with microencapsulated PCM

Experimental Assessment of Hemp Shiv and Green Adhesives to Produce a Biocomposite Material

Thermal Properties of Hemp Shives Used as Insulation Material in Construction Industry

Influence of the Direction of Mixture Compaction on the Selected Properties of a Hemp-Lime Composite

Experimental Analysis of Moisture-Dependent Thermal Conductivity, and Hygric Properties of Novel Hemp–shive Insulations with Numerical Assessment of Their In-Built Hygrothermal and Energy Performance

Characterisation of Hemp Fibres Reinforced Composites Using Thermoplastic Polymers as Matrices

Thermal conductivity of hemp concretes: Variation with formulation, density and water content

Development of a sustainable and innovant hygrothermal bio-composite featuring the enhanced mechanical properties

Utilization of Industrial and Hazardous Waste Materials to Formulate Energy-Efficient Hygrothermal Bio-Composites

Innovative Hemp Shive-Based Bio-Composites: Part I: Modification of Potato Starch Binder by Sodium Meta-Silicate and Glycerol

Characterization of the thermo-mechanical behaviour of Hemp fibres intended for the manufacturing oh high performance composites

Enhancing the Properties of Cement Composites Using Granulated Hemp Shive Aggregates

Physicomechanical, microstructural morphological, and thermal characterizations of jute and coconut husk–based natural fibers reinforced hempcrete hurd composites for building and construction applications

Investigations of Flame Retardancy, Mechanical and Thermal Properties of Woven Hemp/PP Hybrid Composite for Insulating Material Reinforced with Synthetic Silicon and Zinc Oxides

Thermal Conductivity in Concrete Samples with Natural and Synthetic Fibers

Study on Mechanical Properties and Thermal Stability of Polypropylene/hemp Fiber Composites

Development of sunflower husk reinforced polypropylene based sustainable composites: An experimental investigation of mechanical and thermal performance

Studies on sugarcane bagasse/jute fibers reinforced bio-composites for functional thermal insulation materials

Tribological Properties of Hemp Fiber Reinforced Polylactic Acid Bio-Composites: Effect of Different Types of Modification Methods