Abstract:The deformation behavior of a hot roll-bonded stainless steel/carbon steel (STS/CS) clad plate is investigated by focusing on the mechanical properties-microstructure relationship along the plate thickness and clad interface. In detail, the mechanical responses of the STS/CS clad plate and its constituents are evaluated using uniaxial tension, interfacial debonding tests (in normal and shear modes), and various microstructure characterization techniques, which clarify the interfacial heterogeneity of the STS/CS clad plate. The results of experimental analysis present the validity for applying a hybrid numerical–experimental identification procedure for the cohesive zone model (CZM) in the simulation of heterogeneous STS/CS interface using finite element (FE) method. Especially, the mixed-mode bilinear CZM coupled with the inhomogeneously distributed elastic-plastic properties over thickness can be optimized to accurately predict the measured load-displacement curves and springback in the two debonding tests and the V-bending test. Finally, the interfacial failure characteristics of the STS/CS clad are further presented through the comparison between the FE method and fractography analysis at the clad interface. The combined experimental and numerical study reveal interesting aspects beyond commonly reported interfacial behavior. These include: (1) The failure along the STS/CS clad interface is controlled by both “material factors” such as the carbon migration from the interface and its resultant differential strengthening through the thickness, and “process factors” that includes the gradient of strength and temperature across the clad and rolling tools. (2) The major deformation mode is variable according to locations and the mixed normal-shear mode is dominant at tool contacts for initiating the failure during the V-bending test. (3) The interfacial failure mechanism of cladding featured not only in a confined deformation zone where contact directly with tools, but also the exterior area where springback after unloading caused a drastic change of stress state. These abrupt interfacial failures could be clarified via stress state and local damage analysis of the well-reproduced FE model of cladding material.

Resistivity and Formation of Intermetallic Layer in Aluminum-Steel Clad Strip

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Microstructure and Mechanical Properties of Aluminum Clad Steel Plates by Cold Rolling and Annealing Heat Treatment

Twin-Roll Casting of Aluminum-Steel Clad Strips: Static and Dynamic Mechanical Properties of the Composite

Microstructural characterization of AA5183 aluminum clad AISI 1018 steel prepared by electro spark deposition

Identification of the intermetallic compound layer formed at the interface of roll-bonded aluminum-clad steel by thermal annealing

Phase formation and mechanical properties of iron-based intermetallic/steel laminate composites

Microstructure Characterization and Mechanical Properties of Stainless Steel Clad Plate

Calculation of the Intermetallic Layer Thickness in Cold Metal Transfer Welding of Aluminum to Steel

Effect of Annealing Temperature on the Interfacial Microstructure and Bonding Strength of Cu/Al Clad Sheets with a Stainless Steel Interlayer

Temperature evolution, IMC formation, and resulting bonding efficacy in bimetallic tubular components fabricated by a novel friction stir backward extrusion cladding method

Microstructure, Properties and Mechanism of Formation of Aluminum Diffusion Coatings on Heat-Resistant Stainless Steels

Finite Element Modeling and Experimental Verification of a New Aluminum Al-2%Cu-2%Mn Alloy Hot Cladding by Flat Rolling

Formation and Evolution Mechanism of Intermetallic Compounds of Friction Stir Lap Welded Steel/Aluminum Joints

Mechanical behavior and interfacial damage of carbon steel-stainless steel corrosion resisted-alloy (CRA) cladded plate: Hybrid analysis based on experiment and finite element modeling

Interfacial microstructure and mechanical properties of stainless steel clad plate prepared by vacuum hot rolling

Metallurgical interactions in solid/liquid diffusion couples of AA4343/AA3xxx/AA4343 layered aluminum sheet

The effect of the refractory material on the phase transformation parameteres during forming of the Al-8wt%Si-3wt%Cu structure

Study on Microstructure and Properties of AlCoCrFeNi High-Entropy Alloys by Extreme High-Speed Laser Cladding

Study on Direct Chill Continuous Casting of 3003/4004 Clad Slab