Abstract:One of the most universally used materials in construction industries is concrete because of its accessibility, affordability, extended lifespan and resistance to damage against unfavourable weather conditions. However, there is a massive depletion of valuable natural resources for the concrete production. Further, plastic consumption as well as waste generation is increasing day by day which is very much challenging to be managed as it is non-biodegradable and creates various environmental pollution. Thus, the usage of plastic waste as a fractional substitution of natural aggregates in construction industry may mitigate the problems. For the present study, nine concrete mixtures of M30 grade concrete containing recycled plastic waste polyethylene (RPE) and plastic waste polyethylene-terephthalate (WPET) were prepared as a fractional volumetric replacement for both natural coarse aggregates (NCA) and fine aggregates (NFA). The replacement levels were 0%, 5 %, 10%, 15%, 20%, 25%, 30%, 35% and 40% keeping constant the water-cement ratio (0.37).The usage of waste plastic aggregates for preparation of concrete were assessed through different fresh and hardened properties like slump, dry density, compressive strength (CS), flexural strength (FS), split tensile strength (STS) and ultrasonic pulse velocity. The test results corroborates that the slump increased with higher percentage replacement of waste plastic aggregate (PA) in concrete. Further, incorporation of WPET and RPE in concrete reduced the dry density by 10.59 % at 40% mix proportion. It is to be mentioned that, the CS decreases with with increase of partial replacement of natural aggregate with waste PA. The ultrasonic pulse velocity (UPV) also decreased with increase of the PA. The test result also depicted that up to 5% replacement the STS value is almost constant, after that it reduces. Further, in case of FS test, the replacement with waste PA concrete by 10%, the FS improved to 19.91%. Furthermore, the data prediction models of slump, CS, FS and STS were developed by artificial neural network. Moreover, the optimization of mix proportion was conducted by factor response optimizer with composite desirability of 0.65.

Some properties of sustainable concrete with mixed plastic waste aggregate

Concrete Incorporating Recycled Plastic Aggregates: Physical and Mechanical Properties and Predictive Models

High-strain Rate Compressive Behavior of Concrete with Two Different Substituted Recycled Plastic Aggregates: Experimental Characterization and Probabilistic Modeling

Study on green concrete replacing natural fine and coarse aggregate by plastic waste – An experimental and machine learning approach

The Use of Plastic Waste as Replacement of Coarse Aggregate in Concrete Industry

An Investigation of Mechanical Properties of Concrete by Applying Sand Coating on Recycled High-Density Polyethylene (HDPE) and Electronic-Wastes (E-Wastes) Used as a Partial Replacement of Natural Coarse Aggregates

Effects of waste plastics as partial fine-aggregate replacement for reinforced low-carbon concrete pavements

Sustainable development of concrete through treated and untreated plastic waste aggregates

Sustainable Cement Mortar with Recycled Plastics Enabled by the Matrix-Aggregate Compatibility Improvement

Waste aggregate concrete properties using waste tiles as coarse aggregate and modified with PC superplasticizer

Using Recycled Concrete Powder, Waste Glass Powder, and Plastic Powder to Improve the Mechanical Properties of Compacted Concrete: Cement Elimination Approach

The Combined Effect of Glass and Plastic Waste on Concrete Properties: Experimental Study

Use of selected waste materials in concrete mixes

Impact of plastic waste fiber and treated construction demolition waste on the durability and sustainability of concrete

Concrete Performance Produced Using Recycled Construction and By-Product Industrial Waste Coarse Aggregates

Integrating Plastic Waste into Concrete: Sustainable Solutions for the Environment

Performance Evaluation of Plastic Concrete Modified with E-Waste Plastic as a Partial Replacement of Coarse Aggregate

Utilization of plastic waste as replacement of natural aggregates in sustainable concrete: effects on mechanical and durability properties

Sustainable Structural Lightweight Concrete with Recycled Polyethylene Terephthalate Waste Aggregate

Experimental Investigation on Mechanical and Thermal Properties of Concrete Using Waste Materials as an Aggregate Substitution

Studies on partial replacement of waste high density polyethylene (HDPE) and polypropylene (PP) plastic with fine aggregate (FA) on mechanical, durability and thermal properties of M30 and M40 grade concrete