Abstract:A new generation launch vehicle developed by ISRO consists of solid, liquid, and cryogenic stages. Cryogenic stage uses liquid oxygen and liquid hydrogen as oxidizer and fuel, respectively, for propulsion. Fuel and oxidizer are stored in cylindrical tanks with tori-spherical end domes. When the above fluids get depleted from the tanks, dip formation in the liquid surface and subsequent ullage gas entry into the outlet occurs. Formation of surface dip and subsequent gas entry into the outlet is governed by either sink potential phenomenon or vortex phenomenon or combination of both. This could lead to malfunction of the liquid rocket engine. Critical height of propellant from the tank bottom is defined as the elevation at which surface dip forms. Hence, the estimation of critical height is very important in order to quantify unused propellant toward the end of the thrusting phase. Two-phase flow due to vortex can be eliminated by providing either anti-vortex baffle or wire mesh/filter. But it cannot be eliminated due to sink phenomenon unless the outlet is properly designed. Oxidizer tank is provided with a siphoning feed line with wire mesh on the upstream of the inlet to supply contaminant-free liquid oxygen to engine. Published literature on siphoning feed line for the estimation of critical height is very limited. In addition to the above, information on effect of pressure drop due to the presence of wire mesh in the flow path on critical height is also not available. Numerical analysis is carried out using ANSYS CFD software to estimate the critical height for the above siphoning feed line with wire mesh. In order to verify the modeling of wire mesh, two different fluid models (without wire mesh and with wire mesh having zero pressure drop) are used. Oxidizer and gas contained in the tank are idealized as incompressible viscous fluids. Time-dependent Reynolds Averaged Navier Stokes (RANS) equations with continuity and volume fraction equations are solved to estimate the height at which surface dip forms. Numerical simulations are repeated using the fluid model with wire mesh for different pressure drops across it in order to find its effect on critical height. Pressure drop across a wire mesh is due to reduced flow area and is dependent on wire mesh size, density, viscosity, and velocity of fluid. From the numerical investigations, it is found that the presence of wire mesh in the flow path at the upstream of siphoning feed line results in higher critical height due to pressure drop across it. Hence, it is recommended to relocate the wire mesh to the inlet of the siphoning feed line. Another important conclusion is that radial velocity at the inlet of siphoning feed line should be low so that the liquid till its inlet can be utilized. This can be achieved by increasing the bell mouth diameter of the siphoning feed line.

Numerical Analysis on Air Core Vortex Formation in Inclined Cylindrical Tanks

Computational Fluid Dynamics Simulation of Hydrodynamics in an Uncovered Unbaffled Tank Agitated by Pitched Blade Turbines

Numerical simulation of cylinder orientation through a rotating straight expansion duct

Simulation of vortex induced vibration of turbulent flow around a circular cylinder by plane turbulent models

Numerical Simulation of the Accumulation of Heavy Particles in a Circular Bounded Vortex Flow

Numerical Study on the Vortex Motion Patterns Around a Rotating Circular Cylinder and Their Critical Characters

Numerical Simulation of Turbulent Vortex Induced Vibration of a Circular Cylinder Adopted ALE Domain Decomposition Method

Sloshing of a liquid fuel in toroidal tanks with account for capillary effect

Numerical Study of Effect of a Wire Mesh on Fluid Depletion Characteristics of a Cryogenic Propellant Tank

Numerical Simulation of Vortex-Induced Transverse Vibration of a Cylinder with Very Low Mass Ratio

An experimental and numerical study on the behavior of finite-length column vortex

Analysis of Ventilated Cavitation Around A Cylinder Vehicle with Nature Cavitation Using A New Simulation Method

Three-dimensional Numerical Simulation of the Viscous Flow Around a Vertical Circular Cylinder in a Two-Layer Fluid

Experimental study of swirling flow characteristics in a semi cylinder vortex cooling configuration

Study of air-core vortical flow structure induced by a plughole vortex

Numerical Study of Free End Effect of Cylinder with Low Aspect Ratios on Vortex Induced Motion

Directed circulating flows in tanks of moving objects

Direct Numerical Simulations of Horizontally Oblique Flows Past Three-Dimensional Circular Cylinder Near a Plane Boundary

Numerical Simulation and Analysis of Two-Phase Flow Around Cylinder Using Pseudo-Potential Model and Liutex Method

Numerical Study on the Vertical Water Exit of A Cylinder with Cavity

The effect of inner swirl on confined co-axial flow