Abstract:Driven by the rapidly-growing of hybrid and electric vehicles, there is an increasing demand on lithium ion batteries (LIBs) with high energy density, long cycle life, and low cost. One of the most widely used anode materials in LIBs, graphite, only possesses a theoretical specific capacity of about 370 mAh/g, limiting the specific energy of LIBs.1 Recently, conversion-type of electrode materials, i.e. metal oxide and metal sulfide, has been regarded as one of the most promising anode materials for high performance LIBs, due to the low cost and exceptionally high specific capacity (>1000 mAh/g).2 However, these conversion-type electrode materials suffers from several issues, i.e. relatively low conductivity and rapid capacity fade due to irreversible phase change and particle pulverization during cycling. For example, the poor performance of tin oxide is mainly caused by its low intrinsic conductivity, formation of irreversible insulating Li2O phase during discharging, and large volume change.3 To overcome these disadvantages, various methods have been developed, like carbon/tin oxide composites, tin phosphide (Sn4P3). Tin phosphide has a layered structure and can be prepared by a mechanochemical or hydrothermal method. It has shown promising electrochemical performance as the anode in Li-ion batteries.4,5 As the lithium was inserted, Sn4P3 was first converted into lithium phosphides and Sn, followed by lithium-tin alloy formation. The advantage of Sn4P3 is its high capacity and Li+ conductivity of the Li3P. However, it suffers from similar drawbacks as tin oxide, i.e. large volume change and irreversible Li3P phase formation. In this work, we prepared Sn4P3 nanowires by hydrothermal reaction of red phosphorus and tin in ethylenediamine at 200 °C for 40 h. Then, graphite/Sn4P3 composites were prepared by high-energy ball milling for 2 h under Ar atmosphere. Graphite and Sn4P3 were uniformly distributed in the composites, shown in Figure 1a. When tested as the anode materials, the composites showed superior performance compared to Sn4P3 alone. The capacity of Sn4P3 rapidly decreased to around 200 mAh/g after 15 cycles. In comparison, graphite/Sn4P3 composites showed an initial specific capacity of about 1014 mAh/g and maintained a capacity of 782 mAh/g after 50 cycles. In addition, the coulombic efficiency was also much higher in the graphite/Sn4P3 composites, indicating a reversible Li insertion/deinsertion behavior and more stable SEI layer. The rate performance of graphite/Sn4P3 composites was also much better than pure Sn4P3. In conclusion, we report a facile preparation of graphite/Sn4P3 composites with excellent electrochemical performance as anode material in Li-ion batteries. Figure 1

(Digital Presentation) Straightforward Combustion Synthesis of Tin/Carbon Composite As Anode for Lithium-Ion Battery with Long Cycle Life

One-Pot Synthesis of High-Performance Tin Chalcogenides/C Anodes for Li-Ion Batteries

A high-performance tin phosphide/carbon composite anode for lithium-ion batteries

Two-Dimensional SnSe2/CNTs Hybrid Nanostructures As Anode Materials for High-Performance Lithium-Ion Batteries

Facile Preparation of One-Dimensional Hollow Tin Dioxide@carbon Nanocomposite for Lithium-Ion Battery Anode

Advanced Sn/C composite anodes for lithium ion batteries

The Optimized Tin Dioxide-Carbon Nanocomposites As High-performance Anode for Lithium Ion Battery with a Long Cycle Life

Facile Synthesis of a Tin Oxide-Carbon Composite Lithium-Ion Battery Anode with High Capacity Retention

Facile Synthesis of Ultrasmall Tin Oxide Nanoparticles Embedded in Carbon As High-Performance Anode for Lithium-Ion Batteries

Advanced Structures in Electrodeposited Tin Base Anodes for Lithium Ion Batteries

Arc-discharge synthesis of dual-carbonaceous-layer-coated tin nanoparticles with tunable structures and high reversible lithium storage capacity

Stable anodes for lithium-ion batteries based on tin-containing silicon oxycarbonitride ceramic nanocomposites

Superior Cycle Performance of Sn@C/graphene Nanocomposite As an Anode Material for Lithium-Ion Batteries

Investigation of Graphite/Tin Phosphide Composites As the Potential Anode in Li-Ion Batteries

An Elaborate Strategy for Fabricating One-Dimensional Quasi-Hollow Nanostructure of Tin Dioxide@carbon Composite with Improved Lithium Storage Performance

Dual carbon layer hybridized mesoporous tin hollow spheres for fast-rechargeable and highly-stable lithium-ion battery anodes

Ball milling of graphite/tin composite anode materials in a liquid medium

Preparation and Electrochemical Properties of Tin-Iron-Carbon Nanocomposite as the Anode of Lithium-Ion Batteries.

Fabrication of Tin-Carbon Composite Anode Material by Electrospinning and Electrostatic Spray Deposition for Lithium Rechargeable Battery

C@CoSn 2 composite prepared through one-step electro-deoxidation method as anode material of lithium-ion batteries with long-cycle-life and high capacity

Electrochemical Performance of SnO_2-Si/C Composite for Anode Materials of Lithium-Ion Battery