Abstract:A polymer actuator typically responds to only one or two types of stimuli, where sensing and actuation are simultaneously exerted by the same responsive polymer. In cells, sensing and actuation are exerted separately by different biomolecules, which are integrated into nanoscale assemblies to construct the signaling network, making cells a multistimuli responsive and multimodal system. Inspired by the structure–function relationship of the signaling network in cells, we have developed a strategy to select and assemble proper functional polymers into assemblies, where sensing and actuation are exerted by different polymers, and the assemblies can present novel functions beyond that of each polymer component. Three polymers [polyaniline, PANi; poly(N-isopropylacrylamide), PNIPAm; and polydimethylsiloxane, PDMS] are integrated as nodes into a simple energy transduction network, which can be regulated by three molecular factors (pH, kosmotropic anions, and polyethylene glycol). PANi converts the light or electric stimulus into heat, which triggers the actuation of PNIPAm and PDMS. Relying on this energy transduction network, the polymer assembly can respond to six types of stimuli (light, electricity, temperature, water, ions, and organic solvents) and perform different actuation modes, serving as a powerful actuator. Programmable complex deformation upon multiple simultaneous or sequential stimuli has also been achieved by this actuator. An adaptive gripper to catch thin objects and a self-regulating switch to maintain environmental humidity illustrate the wide potential of this actuator for next-generation smart materials and soft robots.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c01549.Photoresponsive behavior of the actuator; mechanical characterization; water-, temperature-, Na2CO3 concentration-, and organic solvent-induced actuation and deformation; programmable deformation driven by sequential stimuli; self-regulated switch to maintain the environmental humidity in a homeostatic range; adaptive grippers; finite element method simulation; optimization of the composition of PANi–PNIPAm; XRD pattern of dried PANi–PNIPAm; photothermal response of PANi aqueous suspension; bending angles of the free neutralized actuator (shown in Figure 2c) upon irradiation; FEA simulation of a fully swelled neutralized actuator under light irradiation; photo and illustrations of fingers moving up and back controlled by a red laser pointer with neutralized actuators acting as knuckles; photothermal performance of the neutralized actuator and the acidified actuator; FEA simulation of the self-curling of an actuator around a hot metal rod; internal stress- and water-induced bending of an actuator exposed to varied humidity; bilayer actuator was saturated in hexane and the swollen PDMS layer caused the actuator to fold into a roll; DSC curves of PANi–PNIPAm swollen in solution with different Na2CO3 concentrations; actuators performing multishape transformation with different length to width ratios and different initial shapes; 2D patterns with saturated Na2CO3 solution inducing the 3D shape of the actuator; and FEA simulation of inverse coiling behavior of an actuator helix upon the change of temperature and CO32– concentration (PDF)Bending and curling of an actuator driven by light (MP4)Artificial sunflower turning toward the direction of the light source (MP4)Light-induced motion of a robot hand and actuators were used as knuckles (MP4)Self-curling of an actuator around a hot steel rod (70 °C) (MP4)Water driving a box with actuators as hinges to close (MP4)Programmable deformation of an actuator in response to sequential stimuli, including light, humidity, heat, and ionic strength (MP4)Self-regulated switch responding to humidity change (MP4)Adaptive grippers that can quickly grasp a hot metal rod or a hot metal wire ball with the PANi–PNIPAm layer in contact with the hot object (MP4)This article has not yet been cited by other publications.

Cellulose‐Reinforced Programmable and Stretch‐Healable Actuators for Smart Packaging

Hygro‐Dynamic and Conductive Actuator That Restructures and Heals by Water

Selectively Aligned Cellulose Nanofibers Towards High-Performance Soft Actuators

High-Sensitivity Multiresponses Cellulose-Based Actuators with Configurable Amplitude

Bio-inspired Hydrogel Actuator with Rapid Self-strengthening Behavior

Stimuli-responsive composite biopolymer actuators with selective spatial deformation behavior

Programmable Polymer Actuators Perform Continuous Helical Motions Driven by Moisture.

Polyurethane Shape Memory Polymer/pH-Responsive Hydrogel Hybrid for Bi-Function Synergistic Actuations

Bilayer Hydrogel Actuators with Tight Interfacial Adhesion Fully Constructed from Natural Polysaccharides

Bio-inspired water resistant and fast multi-responsive Janus actuator assembled by cellulose nanopaper and graphene with lignin adhesion

Rapid Moisture-Responsive Biopolymer Film Actuators

High-performance Cellulose Nanofibers-Based Actuators with Multi-Stimulus Responses and Energy Storage

Photothermal and Humidity Stimulus-Responsive Self-Sensing Soft Actuators for Smart Packaging

Fabricating 3D Moisture- and NIR Light-Responsive Actuators by a One-Step Gradient Stress-Relaxation Process.

Programmable and Reconfigurable Humidity-Driven Actuators Made with MXene (Ti3c2tx)-Cellulose Nanofiber Composites for Biomimetic Applications

Polybenzoxazole Nanofiber-Reinforced Moisture-Responsive Soft Actuators

Vapor and Light Responsive Biocompatible Soft Actuator

Reprogrammable Humidity-Driven Liquid Crystalline Polymer Actuator Enabled by Dynamic Ionic Bonds

Programmable Multistimuli-Responsive and Multimodal Polymer Actuator Based on a Designed Energy Transduction Network

Arbitrarily and repeatedly programmable multi-layer soft actuators via "stress-caching"

Bioinspired Flexible Film As Intelligent Moisture-Responsive Actuators and Noncontact Sensors