Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

CFD analysis of karanja oil methyl ester (KOME) blend B20 and hydrogen using ANSYS-Fluent

CFD Combustion Simulations and Experiments on the Blended Biodiesel Two-Phase Engine Flows

Optimization of Combustion Characteristics of Diesel Engine Fueled by Biofuels and Its Diesel Blends with Additive Titanium Dioxide Nano-Particles

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Experimental investigation of performance, emissions, combustion characteristics, cyclic variations, and exergy efficiency of CI engine fueled with Karanja-camphor oil blends and diesel-camphor oil blends

Computational Study on the Impact of Gasoline-Ethanol Blending on Autoignition and Soot/NOx Emissions under Gasoline Compression Ignition Conditions

Numerical Study of Soot Particles from Low Temperature Combustion of Engine Fueled with Diesel Fuel and Unsaturation Biodiesel Fuels

CFD Modelling of the Co-Gasification of Biomass and Coal Particles in Fluidised Beds

An experimental investigation on preparation and performances of two diesel blends of karanj oil methyl ester

A numerical investigation on a diesel engine characteristic fuelled using 3D CFD approach

Hydrogen, methane and one of their fuel blends combustion: CFD analysis and numerical-experimental comparisons of fixed and mobile applications

Effect of lower and higher alcohol fuel synergies in biofuel blends and exhaust treatment system on emissions from CI engine

Numerical analysis of laminar burning velocity of hydrogen and carbon monoxide-enriched natural gas (HyCONG) blends

Investigation and prediction on emissions and performance of CI engine employing binary and ternary blends with Karanja oil, used cooking oil, and Dunaliella salina oil

Computational study on the impact of gasoline-ethanol blending on autoignition and soot/NOx emissions under low-load gasoline compression ignition conditions

Numerical Investigation of Dual Fuel Combustion on a Compression Ignition Engine Fueled with Hydrogen/Natural Gas Blends

An Experimental Investigation on Performances and Emission Characteristics in a Multi-Cylinder Diesel Engine Using Nahar Oil Biodiesel Blended With Carbon Nano Tube

Optimization of Synthetic Oxygenated Fuels for Diesel Engines

LES and RANS Spray Combustion Analysis of OME3-5 and n-Dodecane

Numerical Investigation of Rotating Detonation Combustion in Annular Chambers

Fossil Diesel, Soybean Biodiesel and Hydrotreated Vegetable Oil: A Numerical Analysis of Emissions Using Detailed Chemical Kinetics at Diesel Engine Like Conditions