Abstract:Powered by the worldwide efforts of research groups experienced in dye‐sensitized, and thin‐film solar cells, perovskite solar cells (PSCs) reached a power conversion efficiency of 25.7% within 10 years. However, the presence of defects and trap density within the active layer's grain boundaries commonly operates as non‐radiative recombination centers. Hence, intensive efforts have been reported to passivate the inevitable bulk and interface defects of the active layer using additives or post‐treatment processing to enhance the efficiency and stability of PSCs. Herein, a facile post‐treatment strategy based on wet processing methylammonium lead triiodide, MAPbI3 (prepared from lead acetate and methylammonium iodide precursors) films with organic amine salts (FABr and FAI) is demonstrated. As a result, high‐quality films of mixed perovskites (FAxMA1‐xPbI3‐xBrx and FAxMA1‐xPbI3) were obtained. The surface treatment has efficiently passivate the defects in the host film, suppressing the non‐radiative carrier recombination. Compared to the control device, the increased open‐circuit voltage (from 0.5 V to 1 V) and fill factor (FF) values of the optimized device based on FAxMA1‐xPbI3 showed a PCE of 16.13%. And our findings revealed that post‐treatment is possible on wet perovskite film aged for a few minutes prior to its post‐treatment, which saved the energy used for pre‐annealing. Post‐treatment has been carried out on wet host film of (MAPbI3) aged for 3 minutes prior to its treatment. The host film, with evident pinholes was changed into smooth morphology and larger grain‐size mixed FAxM1‐xPbI3‐xBrx and FAxMA1‐xPbI3 films upon post‐treatment using FABr and FAI solutions respectively. Compared to the control device, the post‐treated devices had higher fill factor (FF) and a double rise in Open‐circuit voltage (VOC), leading to enhanced device efficiency. Our findings has also proved that post‐treatment is possible on wet films that saved the energy for pre‐annealing during post‐treatment.

Photonic Processing of MAPbI3 Films by Flash Annealing and Rapid Growth for High‐Performance Perovskite Solar Cells

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

Rapid Microwave Annealing for Improved Crystallinity and Morphology of Perovskite Materials

Single‐step post‐production treatment of lead acetate precursor‐based perovskite using alkylamine salts for reduced grain‐boundary related film defects

Improved Crystallinity and Self-Healing Effects in Perovskite Solar Cells Via Functional Incorporation of Polyvinylpyrrolidone

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Confined Growth of High-quality Single-Crystal MAPbBr3 by Inverse Temperature Crystallization for Photovoltaic Applications

Reduced Defects of MAPbI3 Thin Films Treated by FAI for High‐Performance Planar Perovskite Solar Cells

Impacts of MAPbBr3 Additive on Crystallization Kinetics of FAPbI3 Perovskite for High Performance Solar Cells

Facile Face-Down Annealing Triggered Remarkable Texture Development in CH3NH3PbI3 Films for High-Performance Perovskite Solar Cells.

Vacuum-Assisted Thermal Annealing of CH3NH3PbI3 for Highly Stable and Efficient Perovskite Solar Cells

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

Ambient Air Condition for Room-Temperature Deposition of MAPbI Films in Highly Efficient Solar Cells.

Thermal engineering of FAPbI3 perovskite material via radiative thermal annealing and in situ XRD

MACl-Induced Controlled Crystallization in Sequentially Deposited Perovskites for High-Efficiency and Stable Perovskite Solar Cells

Single‐Crystal Seeds Inducing the Crystallization of High‐Performance α‐FAPbI3 for Efficient Perovskite Solar Cells

Amine‐releasable Mediator In‐situ Repair Perovskites for Efficient and Stable Perovskite Solar Cells

To Greatly Reduce Defects Via Photoannealing for High-Quality Perovskite Films.

In situ self‐elimination of defects via controlled perovskite crystallization dynamics for high‐performance solar cells

Thiazole-Induced Surface Passivation and Recrystallization of CH3NH3PbI3 Films for Perovskite Solar Cells with Ultrahigh Fill Factors.

Suppressing the Defects in CsPbI2Br Perovskite Photovoltaic Films Via a Homogeneous Cap-Mediated Annealing Strategy