Abstract:INTRODUCTION: Increased demand for NetSpot and Illuccix as requirement to receive the respective Lutathera and Pluvicto radiotherapies, and monitor subsequent response to treatment, have reinforced the need to develop alternative ways of producing gallium-68 (68Ga). Building on our efforts to produce 68Ga in a liquid target on a GE PETtrace, the goal of this work is to modify the current GE Gallium Chloride cassette using the FASTLab 2 synthesis module to produce [68Ga]GaCl3 equivalent to a 1.85 GBq generator and demonstrate compatibility with FDA-approved kits for production of 68Ga-labeled radiopharmaceuticals.METHODS: 68Ga was produced in a liquid target via the 68Zn(p,n)68Ga reaction. 68Ga was loaded onto various sizes of ZR resins (ZR Load, 0.3 mL, 1 mL, or 2 mL). The loading efficiency was determined using a dose calibrator. After washing with HNO3, 1.75 M HCl was used to elute the ZR Load resin through various sizes of a second ZR resin (ZR CG, 0 mL, 2 mL, 4 mL). Using 0.5 mL fractions, the elution profile was determined. Compatibility of the [68Ga]GaCl3 with NetSpot and Illuccix kits was investigated. Radiochemical purity (RCP) and 4 h stability were determined using radioTLC and radioHPLC. Using a modified [68Ga]GaCl3 cassette and new FASTLab program, 6 validation preparations were conducted using NetSpot and Illuccix kits for which RCP, stability, sterility and suitability were determined. Dual irradiation of 2 liquid targets was also performed, which was used to simultaneously prepare 1 NetSpot and 2 Illuccix kits by diluting the required activity with 0.1 M HCl.RESULTS: The commercially available GE Cassette gave low RCP using commercial FDA kits. To optimize this, the loading efficiency onto ZR Load and the ratio of ZR resin used to load the initial activity and subsequent elution were explored. When using a 2:4 ratio of ZR Load to ZR CG, 97.89 % RCP was observed when a 3.8 mL [68Ga]GaCl3 solution was used. For Dotatate validation, 0.55 mL of buffer was added to 4.2 mL of [68Ga]GaCl3 which gave 1.35 GBq of formulated product. For Illuccix validation, [68Ga]GaCl3 was added to 2.5 mL of buffer which gave 1.52 GBq of [68Ga]Ga-PSMA-11. Formulated products passed package insert quality control (QC) requirements. When dual target irradiations were performed, 2.84 GBq was delivered to an external vial and used to label 1 NetSpot and 2 Illuccix kits simultaneously, and each kit also met or exceeded established QC criteria.CONCLUSION: Methods are reported for using cyclotron-produced 68Ga from a liquid target in conjunction with FDA-approved NetSpot and Illucix kits. By employing a 2 mL ZR Load resin with a 4 mL ZR CG resin, adequate resolution between residual 68Zn and desired 68Ga was achieved. By modifying the FASTLab procedure to retain the final 2.5 mL of eluate from the ZR CG resin, [68Ga]GaCl3 equivalent to a new 1.85 GBq generator was obtained. This was suitable for labeling NetSpot and Illucix kits, resulting in high incorporation of 68Ga (RCP >95 %), which has not previously been demonstrated. Delivering [68Ga]GaCl3 into an external vial and diluting with 0.1 M HCl makes it possible to prepare multiple kits simultaneously. These new procedures should facilitate use of cyclotron-produced [68Ga]GaCl3 for clinical production going.

Experimental Study of the Production of Medical Isotope Gallium-67 on the Beam of Yerevan Cyclotron

Study on Production Method of the {sup 178m2}hf Isomer for Induced Gamma Emission

Investigation of Production Possibility of Medical Isotope 155Tb on Cyclotron C18/18

Production and radiochemical separation of 68 Ge from irradiated Ga–Ni alloy target in 30 MeV cyclotron

Production of copper-64 and gallium-68 with a medical cyclotron using liquid targets

A new preparation of germanium 68

Production of Y-86 and other radiometals for research purposes using a solution target system

Production and Clinical Applications of Radiopharmaceuticals and Medical Radioisotopes in Iran

A novel approach to medical radioisotope production using inverse kinematics: a successful production test of the theranostic radionuclide 67Cu

Investigation of production of medical 82Sr and 68Ge for 82Sr/82Rb and 68Ge/68Ga generators via proton accelerator

Cyclotron-based production of 68Ga, [68Ga]GaCl3, and [68Ga]Ga-PSMA-11 from a liquid target

Development of cooling system of solid state target for irradiation under proton beam of C18 cyclotron

Study of thulium-167 cyclotron production: a potential medically-relevant radionuclide

ARRONAX, a high-energy and high-intensity cyclotron for nuclear medicine

Production of the isotope copper-64 by using natural nickel target with proton energy 17 MeV and beam current 10 μA at cyclotron

Production of 161Tb as a promising Auger electron emitter in Iran

Improved purification of cyclotron [68Ga]GaCl3 for the production of 68Ga radiopharmaceuticals

Production of Medical Radioisotopes with High Specific Activity in Photonuclear Reactions with $γ$ Beams of High Intensity and Large Brilliance

Radioisotopes production using lasers: from basic science to applications

Towards a General Method for Using Cyclotron-Produced Ga68 to Manufacture Clinical and Research Ga68 Tracers