Abstract:Phenol–formaldehyde resin can be used to improve oil recovery; its key lies in its aggregation behavior and blocking strength. However, the traditional phenol–formaldehyde resin used in the petroleum field is all prepared by phenol and formaldehyde. In order to get rid of the dependence on fossil resources and make full use of renewable biomass resources, we used the abandoned walnut shells of the unique agricultural and forestry crops in Gansu province, which contains lignin partially replaced phenol to synthesize the new sulfonated lignin-based phenol–formaldehyde resin (SLPFR). The results showed that the optimum conditions for microwave polymers were polystyrene substitution rate of 20 wt%, decomposition temperature of 160 °C, decommissioning time of 20 min, and sodium hydroxide concentration of 0.3 mol/L. Infrared spectroscopes and scanning telescopes have shown that after disintegration, there was an increased concentration of phosphorus, which had more active spots and was more suitable for replacing phenylphenol-synthetic formaldehyde resins. LC–MS indicated the molecular mass of SLPFR and the possible structure of molecules, indicating the successful synthesis of SLPFR. In this work, the aggregation behavior and dispersion stability of SLPFR were investigated from the composition of formation water. The effects of metal cations (Na + , Mg 2+ , Ca 2+ ) on the dispersion stability of SLPFR in formation water were determined by turbidimetry, and the effects of metal cations on the particle size and zeta potential of the SLPFR system were measured by dynamic light scattering method and electrophoretic light scattering method. The stability of the aggregate structure of the SLPFR system was calculated by combining the fractal dimension. In this paper, the surfactant + SLPFR system and partially hydrolyzed polyacrylamide (HPAM) + SLPFR system were designed for the specific conditions of oil reservoirs, and the effects of metal cations on the aggregation behavior and dispersion stability of these two systems were studied. Based on the above comprehensive analysis, aggregation models were constructed to describe the aggregation behavior and dispersion stability of the HPAM + surfactant + SLPFR system. This makes it possible to predict in real time the migration and plugging of SLPFR aggregates in formation water.

Development and Evaluation of a Novel Sulfonated Phenol–Formaldehyde Resin with High Dispersion Stability

Silicone-modified Phenolic Resin: Relationships Between Molecular Structure and Curing Behavior

Novel Silicon-Modified Phenolic Novolac Resins: Non-isothermal Curing Kinetics, and Mechanical and Thermal Properties of Their Biofiber-Reinforced Composites

Molecular modeling of phenol formaldehyde resin—surfactant and its dispersion stability in salt solution

Sustainable, Biobased Silicone with Layered Double Hydroxide Hybrid and Their Application in Natural-Fiber Reinforced Phenolic Composites with Enhanced Performance

Properties of Phenolic Molding Compounds Reinforced with Sisal Fiber

Preparation of Magnesium Hydroxide Sulfate Whisker-Phenolic Resin Composite by In-Situ Polymerization Technique and Its Properties

Novel silicon-modified phenolic novolacs and their biofiber-reinforced composites: Preparation, characterization and performance

Sulfonated lignin-based phenol–formaldehyde resin: stability and structure changes during aggregation

Optimization of preparation techniques for high-temperature resistant waterborne phenolic-epoxy resin emulsion under low carbon background

Experimental Study on Phenol-Formaldehyde Resin Aggregates as In-Depth Conformance Control Agents Stabilized by Polymer

Synthesis and Characterization of an Environmentally Friendly Phenol–Formaldehyde Resin Modified with Waste Plant Protein

Synthesis of a water‐soluble high hydroxymethyl content phenolic resin crosslinker and the associated polyacrylamide weak gel property investigation

Study on Water-Soluble Phenolic Resin Gels for High-Temperature and High-Salinity Oil Reservoir

Salt-Responsive Phenol Formaldehyde Resin: Changes of Interface Energy on the Aggregation Process

Phenolic Resin Modified by Boron-Silicon with High Char Yield

Synthesis of Silicon Hybrid Phenolic Resins with High Si-Content and Nanoscale Phase Separation Structure

Synthesis and Characterization of a Fluorinated Phenolic Resin/phenolic Resin Blend

Synthesis of Phenol Formaldehyde (PF) Resin for Fast Manufacturing Laminated Veneer Lumber (LVL)

Enhanced mechanical properties, thermal stability of phenolic‐formaldehyde foam/silica nanocomposites via in situ polymerization

Design and Preparation of Shape Memory Phenol–formaldehyde Foam Composites with Excellent Thermal Stability and Mechanical Properties