Abstract:Surface oxidation is known to have a negative impact on the flotation performance of sulphide minerals. This is because severe oxidation makes it more difficult to process low-grade sulphide minerals, which reduces the recovery of valuable minerals during flotation. It may be possible to quantitatively correlate the rate/level of oxidation to oxidized sulphide ores using simple surface analytical techniques. This, if done well, could eliminate the need for numerous mineralogical tests, saving both time and money. This study investigated the EDTA Extraction Technique and Oxygen consumption factor (OCF) Technique as possible techniques to quantitatively describe oxidation levels in different ore types with different mineral compositions and grades. The aim was to determine if the changes in the surface character generated by oxidation are linked to a measurement obtained from the selected techniques. The techniques were validated on fresh ores of varying grades; high grade Cu (HG Cu) and Upper Group 2 (UG2). The two ores were then ground to generate varying particle size distributions and liberation profiles to study the link between oxidation, particle size and liberation. Based on ore type and sulphide liberation, the tests attempted to provide an indicator of feed grade and surface oxidation. Flotation is used as a diagnostic for the parameters mentioned. The results showed that (for Ore A/UG2) as particle size decreased (from grind size 40 %–75 μm), the recovery increased until it hit a maximum (grind size 60 %–75 μm) before monotonically declining (to grind size 80 %–75 μm). The OCF and EDTA values increased as the grind size became finer. The grind size 80 %–75 μm had suffered significantly more oxidation than the other grind sizes and this was indicated by the high OCF and the EDTA value. The liberated base metal sulphides (BMS) for Ore B (HG Cu) was generally consistent throughout the three grind sizes, however, the highest recovery was achieved by the grind size 80 %–75 μm (95.11 %), followed by grind sizes 60 %–75 μm and 40 %–75 μm respectively (92.25 % and 90.86 %). The recovery of this ore increases as the grind size becomes finer. Ore B demonstrated a direct correlation between the OCF and EDTA value for ore B increased as the grind size became finer, and the recovery. It is possible that the particles that were ground to achieve particle size 80 %–75 μm were at their most hydrophobic state, owing to the increased liberation of the BMS, particularly chalcopyrite.

Current Status of Copper-Ore Processing: A Review

Sustainable Use of Copper Resources: Beneficiation of Low-Grade Copper Ores

A review of the effects of the grinding environment on the flotation of copper sulphides

The Challenges and Prospects of Recovering Fine Copper Sulfides from Tailings Using Different Flotation Techniques: A Review

Using a Modified Reagent in the Enrichment of Oxidized Copper Ores

Flotation of Iron Ores: A Review

Sources, Performance and Mechanisms of Metal Ions in the Flotation Process of Copper, Lead, and Zinc Ores: A Review

OPTIMIZATION OF FLOTATION OF THE QALEH ZARI MINE OXIDIZED COPPER ORE SAMPLE BY THE SEQUENTIAL SULFIDATION APPROACH USING THE RESPONSE SURFACE METHOD TECHNIQUE

Beneficiation of Lead-Zinc Ores – A Review

Improving the Copper-Molybdenum Ores Flotation Technology Using a Combined Collecting Agent

Copper solvent extraction on the African Copperbelt: From historic origins to world-leading status

ENERGY EFFICIENCY INCREASING OF ORE ENRICHMENT WASTES’ PROCESSING BY ELECTRICAL DISCHARGE METHOD

Study on the extraction of metals from tails of flotation enrichment of copper sulfide ores

Iron Oxide-Copper Mineral Associations in Supergene Zones: Insights into Flotation Challenges and Optimization Using Response Surface Methodology

Current Status of the Effect of Seawater Ions on Copper Flotation: Difficulties, Opportunities, and Industrial Experience

Tennantite and Enargite Rejection in the Copper Flotation—A Mini-Review

Promising methods for hydrometallurgical processing of copper slag

Comprehensive Review on Metallurgical Upgradation Processes of Nickel Sulfide Ores

The Development of Innovated Complex Process for Treatment of Old Flotation Tailings of Copper-Zinc Sulfide Ore

The use of simple analytical techniques to assess surface oxidation of sulphide ores

Hydrometallurgical processing of chalcopyrite: A review of leaching techniques