Abstract:Composite polymer membranes were obtained using the so-called dry phase inversion and were used for desalination of diluted saline water solutions by pervaporation (PV) method. The tests used a two-layer backing, porous, ultrafiltration commercial membrane (PS20), which consisted of a supporting polyester layer and an active polysulfone layer. The active layer of PV membranes was obtained in an aqueous environment, in the presence of a surfactant, by cross-linking a 5 wt.% aqueous solution of polyvinyl alcohol (PVA)—using various amounts of cross-linking substances: 50 wt.% aqueous solutions of glutaraldehyde (GA) or citric acid (CA) or a 40 wt.% aqueous solution of glyoxal. An ethylene glycol oligomer (PEG 200) was also used to prepare active layers on PV membranes. Witch its help a chemically cross-linked hydrogel with PVA and cross-linking reagents (CA or GA) was formed and used as an active layer. The manufactured PV membranes (PVA/PSf/PES) were used in the desalination of water with a salinity of 35‰, which corresponds to the average salinity of oceans. The pervaporation method was used to examine the efficiency (productivity and selectivity) of the desalination process. The PV was carried at a temperature of 60 °C and a feed flow rate of 60 dm3/h while the membrane area was 0.005 m2. The following characteristic parameters of the membranes were determined: thickness, hydrophilicity (based on contact angle measurements), density, degree of swelling and cross-linking density and compared with the analogous properties of the initial PS20 backing membrane. The physical microstructure of the cross-section of the membranes was analyzed using scanning electron microscopy (SEM) method.

Desalination by membrane pervaporation: A review

Desalination by pervaporation: A review

Membrane Distillation for Desalination and Other Separations

Water Permeance, Permeability and Desalination Properties of the Sulfonic Acid Functionalized Composite Pervaporation Membranes

High Performance Graphene Oxide/polyacrylonitrile Composite Pervaporation Membranes for Desalination Applications

High-performance sulfosuccinic acid cross-linked PVA composite pervaporation membrane for desalination

Tailoring the Microstructure of Poly(vinyl Alcohol)-Intercalated Graphene Oxide Membranes for Enhanced Desalination Performance of High-Salinity Water by Pervaporation

The Efficiency of Polyester-Polysulfone Membranes, Coated with Crosslinked PVA Layers, in the Water Desalination by Pervaporation

Study on High-Performance Pervaporation Desalination Membranes Prepared by Interfacial Reactions Between Two Aqueous Monomers

Study of Hybrid PVA/MA/TEOS Pervaporation Membrane and Evaluation of Energy Requirement for Desalination by Pervaporation

Pervaporation membrane materials: Recent trends and perspectives

Robust construction of polyvinyl alcohol intercalated graphene oxide nanofiltration membrane for desalination via pervaporation

Fabricating thin-film composite membranes for pervaporation desalination via photo-crosslinking

Flexible layered double hydroxides array composite membrane for efficient pervaporation desalination

Preparation and Characterization of PVDF/nonwoven Fabric Flat-Sheet Composite Membranes for Desalination Through Direct Contact Membrane Distillation

Controllable Cross-Linking of VA-co-VAm/PAN Composite Membranes for Efficient Pervaporation Desalination under Extreme Ph Conditions

Surface Engineering Through Biomimicked Structures and Deprotonation of Poly(vinyl Alcohol) Membranes for Pervaporation Desalination

Fabrication of pervaporation desalination membranes with excellent chemical resistance for chemical washing

Composite membranes from bio-inspired catechol-amine coatings for pervaporation desalination

Development of new pervaporation composite membranes for desalination: Membrane characterizations and experimental permeation data

Enhancing the property of composite pervaporation desalination membrane by fabricating a less resistance substrate with porous but skinless surface structure