Abstract:Metallic components fabricated with powder bed fusion additive manufacturing (AM) processes are known to have defects arising from liquid-solid phase transformation. Friction stirring can be an effective alternative source of heat, as evidenced in some of the recently developed powder deposition-based solid-state AM processes. However, they possess practical issues such as making compacted powder feedstock beforehand, consolidation of powder filler inside the tool during deposition followed by necessary extrusion, and significant flash formation, among a few. This paper proposed a novel powder bed friction stir (PBFS) additive manufacturing process inside a specifically designed mould that could potentially mitigate such issues in the existing technologies. The process was successfully demonstrated by building single-track and parallel double-track 3D structures layer-by-layer from an AA6061 powder bed using a rotating non-consumable friction stirring tool. Furthermore, for a better understanding of the underlying process mechanics, deposits were analyzed for their surface topography, microstructural evolution, and mechanical performance under different heat inputs as well as different print locations. Different heat inputs were applied by varying the friction-stirring pitch (FS pitch) from 'Low' to 'High'. The print locations analysis was carried out in a parallel double-track fabricated at the optimal FS pitch. The results revealed that the 'High' FS pitch yielded an increased percentage of recrystallized grains and a fraction of high-angle grain boundaries as well as a larger average grain size due to the high heat input, better material intermixing, and the dominance of continuous dynamic recrystallization. As a result, an improved mechanical performance, except for the microhardness, was observed. The 'High' FS pitch also exhibited an improved surface topography. The results also revealed that the relative dominance of the re-stirring-induced recrystallization and the reheating-induced plastic deformation was the key factor for the variation of the microstructure in the longitudinal, transverse, and short-transverse directions. A gradual decrease in the tensile strength was observed from the 'Top' to the 'Bottom' segments of the overlapped region, contrary to the central region of a track.

Experimental investigation and parametric optimization of friction stir powder additive manufacturing process for aerospace-grade Al alloy

Development and analysis of a powder bed friction stir (PBFS) additive manufacturing process for aluminium alloys: A study on friction-stirring pitch (ω/v) and print location

Multi-objective optimization of friction stir additively manufactured Al-7075 multi-layered laminates

Optimisation of FSP parameters in cast magnesium alloy using hybrid GRA methodology

Optimizing friction stir processing parameters for aluminium alloy 2024 reinforced with SiC particles: A taguchi approach of investigation

Influence of Tool Pin Profiles on Aluminium Alloy A356 and Ceramic-Based Nanocomposites for Light Weight Structures by Friction Stir Processing

Optimization of Friction Stir Processing Parameters to Improve Mechanical Properties and Microstructure of Al5083 Aluminum Alloy Reinforced with AlCoCrFeNiSi High-Entropy Alloy

Parametric Optimization of FDM Process for PA12-CF Parts Using Integrated Response Surface Methodology, Grey Relational Analysis, and Grey Wolf Optimization

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Parameter optimization of friction stir spot welded Al 6061 and CFRTP PA6 with surface treatment and interfacial adhesion

Experimental and numerical analysis of friction stir additive manufacturing of 2024 aluminium alloy

Advancements in Aluminum-Based Composite Manufacturing: Leveraging ZrO2 Reinforcement through Friction Stir Process

Microstructure Refinement and Augmenting Mechanical Properties of Mg Alloy Using Friction Stir Processing

Optimizing Friction Stir Welding of Dissimilar Grades of Aluminum Alloy Using WASPAS

Friction Stir Processing of Aerospace Aluminum Alloy by Addition of Carbon Nano Tube

Microstructural and sensor data analysis of friction stir processing in fabricating Al6061 surface composites

Friction Stir Powder Additive Manufacturing of Multi-track Depositions of Al 6061 Alloy for Cladding and 3D Printing Applications

Additive friction stir deposition of al 7075 parts and the effect of heat treatment on microstructure, electroconductivity, and mechanical properties

Influence of friction stir processing on microstructure and mechanical properties of AA6061 reinforced with Zr and Ni metallic particles

Optimize Process Parameter of FDM Techniques to Improve Mechanical Properties of Aerospace Application

Application of friction stir surface treatment for modification of peripheral coarse grain structure and mechanical properties of AZ31 Mg alloy