Abstract:It has been long understood that fretting differs from sliding wear in that the relative displacement between the bodies is generally smaller than the size of the contact between them, with debris ejection from the contact thus playing an important role in the behaviour of the contact in fretting. Whilst these ideas were clearly articulated more than 30 years ago via Godet's third-body approach and Berthier's concept of the tribology circuit, calculation of wear rates in fretting have continued to employ Archard's wear equation (or approaches directly derived from it), despite this approach assuming that the rate of wear is controlled by the rate of generation of wear debris (as opposed to the rate of its ejection from the contact). It has been shown recently that when debris ejection is the rate-determining-process in fretting, the instantaneous rate of wear is inversely proportional to a characteristic dimension of the wear scar. When non-conforming specimen pair geometries (such as cylinder-on-flat) are employed in fretting testing, the wear scar size increases as wear proceeds, and thus the instantaneous rate of wear decreases. In this paper, wear equations have been derived for three commonly employed non-conforming pair specimen geometries, which all take the form <math>Vw=KRn−1Edn</math> (<math>Vw</math> is the wear scar volume, <math>R</math> is the radius of the non-plane specimen(s) in the pair and <math>Ed</math> is the frictional energy dissipated) where <math>n</math> varies between 0.67 and 0.8 depending upon the geometry and assumptions made regarding the governing equation. It is argued that the assumptions on which the analysis is based are most valid for the cylinder-on-flat contact configuration with fretting perpendicular to the cylinder axis where the length of the line contact is large compared to the wear scar width. It is demonstrated that, despite the often apparently good fit of experimental data to an Archard-type equation, it is not appropriate to employ such Archard-type approaches to the analysis of fretting data in situations where debris ejection is the rate-determining-process. The equations derived in this paper relating wear scar size to some measure of the duration of the test should be used for such analysis instead of the linear relationships generally employed in previous work.

Adjusting for Running-in: Extension of the Archard Wear Equation

Archard’s wear law revisited to measure accurate wear coefficient considering actual sliding velocity

Prediction of Archard's wear coefficient for metallic sliding friction assuming a low cycle fatigue wear mechanism

Large scale multi-parameter analysis of wear of self-mated 100Cr6 steel – A study of the validity of Archard's law

Numerical calculation of wear in rolling contact based on the Archard equation: Effect of contact parameters and consideration of uncertainties

Micromechanics of material detachment during adhesive wear: A numerical assessment of Archard's wear model

Correction of Archard equation for wear behavior of modified pure titanium

Wear time-dependent reliability analysis using Bayesian inference

Experimental Analysis and Wear Prediction Model Based on Friction Heat for Dry Sliding Contact

Wear-life analysis of deep groove ball bearings based on Archard wear theory

Contact size and debris ejection in fretting: The inappropriate use of Archard-type analysis of wear data and the development of alternative wear equations for commonly employed non-conforming specimen pair geometries

Dynamic changes of mechanical properties induced by friction in the Archard wear model

On the Possibility of Frictional Damping with Reduced Wear: A Note on the Applicability of Archard's Law of Adhesive Wear under Conditions of Fretting

Speculations on the theory of adhesive wear

A parameter-free mechanistic model of the adhesive wear process of rough surfaces in sliding contact

A Deterministic Mixed Lubrication Model for Parallel Rough Surfaces Considering Wear Evolution

GENERALIZED ARCHARD LAW OF WEAR BASED ON RABINOWICZ CRITERION OF WEAR PARTICLE FORMATION

On the Uniqueness of Wear Coefficient for Abrasive Wear at Nanoscale

How accurate is the Archard law to predict wear of UHMWPE in hard-on-soft hip implants? A numerical and experimental investigation

A Closer Look at the Contact Conditions of a Block-on-Flat Wear Experiment

Waviness Affects Friction and Abrasive Wear