Abstract:This work was designed to observe and further correct the physical matrix effect in the analysis of solid materials with laser-induced breakdown spectroscopy (LIBS), an effect that arises when a calibration model established with a set of certified reference materials (CRMs) with a smooth surface is used for prediction with LIBS spectra acquired from materials with an irregular surface, such as scraps produced by an automobile shredder for example. CRMs of an aluminum alloy were prepared in such way that one half of the surface of each sample was mechanically destroyed to present an asperity similar to a scrap. LIBS measurements were then performed in the two halves of the sample surface in the same conditions. The spectra acquired from the smooth part of the sample surface served as a training data set to train calibration models, while those taken from the irregular part of the surface were used as a validation data set to assess the prediction performance of the calibration models. Four elements (magnesium, silicon, iron, and zinc), which are important for the recycling of aluminum alloy scraps, were analyzed. The study started with univariate models, where the influence of the surface asperity was clearly observed. A first correction with internal standard normalization showed limited effectiveness. Further improvements were attempted using a machine learning-based multivariate regression, where the calibration performance of the models was significantly improved thanks to an optimized correction of the chemical matrix effect, whereas the prediction performance was still unsatisfactory due to the surface asperity alternation of the validation samples. A transfer learning-based regression model, where a part of the irregular samples joined the training data set, was thus developed to effectively correct both chemical and physical matrix effects and allowed significantly improved the performances of both calibrations, with a relative error of calibration (REC) at 2.3%, and prediction for irregular samples, with a relative error of prediction (REP) at 16.3% on average for the 4 tested elements.

Calibration Transfer for ChemCam Spectral Data from Different Laser-Induced Breakdown Spectrometers Via a Deep Extreme Learning Machine

Improving laser-induced breakdown spectroscopy regression models via transfer learning

Broadening the Scope of Food Quality Control: a Calibration Transfer Strategy for Minimizing External Influences on Spectral Analysis

Targetless Calibration of LiDAR-IMU System Based on Continuous-time Batch Estimation

From Machine Learning to Transfer Learning in Laser-Induced Breakdown Spectroscopy: the Case of Rock Analysis for Mars Exploration

From machine learning to transfer learning in laser-induced breakdown spectroscopy analysis of rocks for Mars exploration

The Application of Piecewise Direct Standardization with Snv in Calibration Transfer of Raman Spectra

When Convolutional Neural Networks Meet Laser-Induced Breakdown Spectroscopy: End-to-End Quantitative Analysis Modeling of ChemCam Spectral Data for Major Elements Based on Ensemble Convolutional Neural Networks

A New Method for Cross-Calibration Between LIBS Systems based on Domain Adaptive Fully Connected Network

Accurate Quantitative Analysis of LIBS With Image Form Spectra by Using a Hybrid Deep Learning Model of a Convolutional Block Attention Module-Convolutional Neural Network-Long Short-Term Memory

A transferred multitask regularization convolutional neural network (TrMR-CNN) for laser-induced breakdown spectroscopy quantitative analysis

Estimating Scale Discrepancy in Bayesian Model Calibration for ChemCam on the Mars Curiosity Rover

Investigation into the Affect of Chemometrics and Spectral Data Preprocessing Approaches upon Laser-Induced Breakdown Spectroscopy Quantification Accuracy Based on MarSCoDe Laboratory Model and MarSDEEP Equipment

A Target-based Calibration Method for LiDAR-Visual-Thermal Multi-Sensor System.

Machine learning in laser-induced breakdown spectroscopy: A review

Transfer Learning Improves the Prediction Performance of a LIBS Model for Metals with an Irregular Surface by Effectively Correcting the Physical Matrix Effect

Machine Learning Allows Calibration Models to Predict Trace Element Concentration in Soils with Generalized LIBS Spectra

Enhancement of spectral model transferability in LIBS systems through LIBS-LIPAS fusion technique

Machine Learning Allows Calibration Models to Predict Trace Element Concentration in Soil with Generalized LIBS Spectra

Systematic prediction error correction: A novel strategy for maintaining the predictive abilities of multivariate calibration models

Incorporating Domain Knowledge into Machine Learning for Laser-Induced Breakdown Spectroscopy Quantification