Abstract:Janus structural interfacial vaporization by separating the solar absorber from the bulk working fluid has attracted tremendous attention due to its low heat losses and high solar conversion efficiency for desalination, water purification, energy generation, etc. However, a totally separated double-deck structure with a discontinuous interfacial transition and inefficient photothermic materials undermines its long-term use and large-scale practical exploitation. Herein, a low-cost Janus monolithic chitosan aerogel with continuous aligned run-through microchannels has been demonstrated to have a highly efficient photothermic effect on seawater desalination and wastewater purification. The top solar absorber layer enhances broadband light absorption and photothermal conversion efficiency via the multiple internal reflection of incident light in the aligned microchannels. Moreover, the insulating/hydrophilic bottom layer promotes water transportation and heat localization, and simultaneously prevents salt/fouling accumulation. As a result, a long-term solar vaporization rate of ∼1.76 kg m<sup>–2</sup> h<sup>–1</sup> is achieved, corresponding to a light-to-vapor efficiency of ∼91% under 1 sun irradiation. Notably, the large-vessel microchannels throughout the aerogel and favorable swelling property provide sufficient water replenishment and storage for completely isolating self-contained evaporation, illustrating an enhanced and time-extended self-contained solar steam generation. Such a low-cost bilayer aerogel with remarkable cycling stability in various fluids offers potential opportunities for freshwater production in remote rural areas.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c02198?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c02198</a>.Pore size distribution and surface morphology of CS, CCS-60, CCS-240 and CCS-480; FT-IR spectra of the CCS-240 and CCS-480; Raman spectra of CCS-60, CCS-240 and CCS-480; XPS spectra of NFs and high–resolution XPS spectra of CS, CCS-60, CCS-240 and CCS-480 for N 1s and C 1s; thermogravimetric analysis (TGA) and differential thermal gravimetric (DTG) analysis of CS, CCS-60, CCS-240 and CCS-480; axial compressive stress-strain curves of CCS-240 and CCS-480; photographs of the soaking unchanged CCS-60 after two months; transmittance and reflectance spectra of CCS-240 and CCS-480; the hydrophilic property of CS, CCS-60, CCS-240 and CCS-480; calculation of evaporation conversion (photothermal) efficiency of CCS; interfacial water evaporation efficiency from the selected typical publications; the total pore volume of CS and CCS; calculation of estimating the cost of CCS; photographs of the swollen changes of CCS immersed in a solution with different pH values over time; calculation of absorption capacity; swelling measurements; evaporation mass loss in suspending and containing configurations; and infrared images of the solar evaporation processes of CCS-60 containing configuration at the beginning and after 5 h later (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c02198/suppl_file/am1c02198_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Efficient Solar‐Powered Interfacial Evaporation, Water Remediation, and Waste Conversion Based on a Tumbler‐Inspired, All‐Cellulose, and Monolithic Design

Efficient Water Transport and Solar Steam Generation Via Radially, Hierarchically Structured Aerogels

Solar‐Driven Interfacial Evaporation and Self‐Powered Water Wave Detection Based on an All‐Cellulose Monolithic Design

Boosting interfacial solar steam generation by three-dimensional bilayer cellulose aerogels

3D Vascular-structured Flame-retardant Cellulose-based photothermal aerogel for Solar-driven interfacial evaporation and wastewater purification

Textile waste derived cellulose based composite aerogel for efficient solar steam generation

Exceeding the Theoretical Limit of Interfacial Evaporation Efficiency by Using the Carbon-Based Aerogel Evaporator with Cold Evaporation Surface

An integrated cellulose aerogel evaporator with improved thermal management and reduced enthalpy of evaporation using a hierarchical coordinated control strategy

Integrated Photothermal Aerogels with Ultrahigh-Performance Solar Steam Generation

Carbon coated vermiculite aerogels by quick pyrolysis as cost-effective and scalable solar evaporators

A 3D aerogel evaporator for efficient solar interfacial evaporation: Breaking through the upper limit of steam production rate

Nanofibrous Aerogels with Vertically Aligned Microchannels for Efficient Solar Steam Generation

Photothermal Aerogel Beads Based on Polysaccharides: Controlled Fabrication and Hybrid Applications in Solar-Powered Interfacial Evaporation, Water Remediation, and Soil Enrichment

Multifunctional Super‐Hydrophilic MXene/Biomass Composite Aerogel Evaporator for Efficient Solar‐Driven Desalination and Wastewater Treatment

Marine biomass-derived composite aerogels for efficient and durable solar-driven interfacial evaporation and desalination

All-weather Photothermal-Electrothermal Integrated System for Efficient Solar Steam Generation

Self-contained Janus Aerogel with Antifouling and Salt-Rejecting Properties for Stable Solar Evaporation

Shape-controlled fabrication of cost-effective, scalable and anti-biofouling hydrogel foams for solar-powered clean water production

Bacterial cellulose-based porous Janus aerogels for efficient interfacial solar steam generation

Self-interlocked down Biomass-based carbon fiber aerogel for highly efficient and stable solar steam generation

Amphipathic Janus Nanofibers Aerogel for Efficient Solar Steam Generation