Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Formation of a nanoporous PbI2 layer framework via 4‐tBP additive to improve the performance and stability of two‐step prepared hybrid perovskite solar cells under ambient conditions

Disperse PbI 2 clusters with 4-Difluoromethyl-Benzylamine Hydrochloride to improve the efficiency and stability of perovskite solar cells

4-Tert Butylpyridine Induced MAPbI3 Film Quality Enhancement for Improving the Photovoltaic Performance of Perovskite Solar Cells with Two-Step Deposition Route

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Multistrategy Toward Highly Efficient and Stable CsPbI2Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

PbI6 Octahedra Stabilization Strategy Based on π‐π Stacking Small Molecule Toward Highly Efficient and Stable Perovskite Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Enhanced Stability and Solar Cell Performance Via Π-Conjugated Lewis Base Passivation of Organic Inorganic Lead Halide Perovskites

High-Light-Tolerance PbI 2 Boosting the Stability and Efficiency of Perovskite Solar Cells

Stiffening the Pb-X Framework through a π-Conjugated Small-Molecule Cross-Linker for High-Performance Inorganic CsPbI 2 Br Perovskite Solar Cells

High-Light-Tolerance PbI2 Boosting the Stability and Efficiency of Perovskite Solar Cells.

Hexamethylphosphoramide-Assisted Structure and Morphology Regulation of a PbI2 Film for Air-Processed Efficient Perovskite Solar Cells Via a Two-Step Deposition Method

Heterojunction Incorporating Perovskite and Microporous Metal–Organic Framework Nanocrystals for Efficient and Stable Solar Cells

Toward High-Efficiency and Thermally-Stable Perovskite Solar Cells: A Novel Metal-Organic Framework with Active Pyridyl Sites Replacing 4-Tert-butylpyridine

(Invited) Improvement of Perovskite Films and the Perovskite/TiO2Interface

Toward desirable 2D/3D hybrid perovskite films for solar cell application with additive engineering approach

Adjustable Skeleton of Bilateral Lewis Base Passivator for CsPbI 3 Perovskite Solar Cells with PCE over 20% and Superior Stability

Improvement of Thermal Stability and Photoelectric Performance of Cs2PbI2Cl2/CsPbI2.5Br0.5 Perovskite Solar Cells by Triple-Layer Inorganic Hole Transport Materials

Synergistic Effect of Fluorinated Passivator and Hole Transport Dopant Enables Stable Perovskite Solar Cells with an Efficiency Near 24%