Abstract:Polymers have an excellent effect in terms of moderating fast neutrons with rich hydrogen and carbon, which plays an indispensable role in shielding devices. As the shielding of neutrons is typically accompanied by the generation of γ-rays, shielding materials are developed from monomers to multi-component composites, multi-layer structures, and even complex structures. In this paper, based on the typical multilayer structure, the integrated design of the shield component structure and the preparation and performance evaluation of the materials is carried out based on the design sample of the heat-resistant lightweight polymer-based interlayer. Through calculation, the component structure of the polymer-based materials and the three-layer thickness of the shield are obtained. The mass fraction of boron carbide accounts for 11% of the polymer-based material. Since the polymer-based material is the weak link of heat resistance of the multilayer shield, in terms of material selection and modification, the B4C/TiO2/polyimide molded plate was prepared by the hot-pressing method, and characterization analysis was conducted for its structure and properties. The results show that the ball milling method can mix the materials well and realize the uniform dispersion of B4C and TiO2 in the polyimide matrices. Boron carbide particles are evenly distributed in the material. Except for Ti, the other elemental content of the selected areas for mapping is in good agreement with the theoretical values of the elemental content of the system. The prepared B4C/TiO2/polyimide molded plate presents excellent thermal properties, and its glass transition temperature and initial thermal decomposition temperature are as high as 363.6 °C and 572.8 °C, respectively. In addition, the molded plate has good toughness performs well in compression resistance, shock resistance, and thermal aging resistance, which allows it to be used for a long time under 300 °C. Finally, the prepared materials are tested experimentally on an americium beryllium neutron source. The experimental results match the simulation results well.

Mechanical Properties of High Temperature Resistant Energy Storage Dielectric Materials and Radiation Scintillation Detection Composite Materials in Bridge Construction

High- K Polymer Nanocomposites Filled with Hyperbranched Phthalocyanine-Coated BaTiO3 for High-Temperature and Elevated Field Applications.

"Grafting To" Route To Pvdf-Hfp-Gma/Batio3 Nanocomposites With High Dielectric Constant And High Thermal Conductivity For Energy Storage And Thermal Management Applications

Modulating polarization and carrier migration characteristics via constructing sandwich-structured heterojunction interfaces for achieving excellent high-temperature energy storage properties in polymer nanocomposites

Modulating Electron Traps of PEI-based Nanocomposites for Superb Capacitive Performance over a Broad Temperature Range

Interface-Strengthened Polymer Nanocomposites with Reduced Dielectric Relaxation Exhibit High Energy Density at Elevated Temperatures Utilizing a Facile Dual Crosslinked Network.

Interfacial crosslinking enabled super-engineering polymer-based composites with ultra-stable dielectric properties beyond 350 °C

Development of Radiation Hard Scintillators

Investigation Of Microstructure And Conductive Mechanism Of High Density Polyethylene/Carbon Black Particle Composite By Positron Annihilation Lifetime Spectroscopy

Flexible PVDF/CNTs/Ni@CNTs Composite Films Possessing Excellent Electromagnetic Interference Shielding and Mechanical Properties under Heat Treatment

Enhancing high-temperature capacitor performance of polymer nanocomposites by adjusting the energy level structure in the micro-/meso-scopic interface region

Fabrication, Structural Characterization, and Photon Attenuation Efficiency Investigation of Polymer-Based Composites

Effect of Hybrid Lead-Pva Fibers on Microstructure and Radiation Shielding Properties of High-Performance Concrete

Resurfaced CsPbBr3 Nanocrystals Enable Free Radical Thermal Polymerization of Efficient Ultrafast Polyvinyl Styrene Nanocomposite Scintillators

Energy Storage and Mechanical Performance of PVDF-HFP/SWCNT Composites with Low Permeability

Excellent High-Temperature Energy Storage Capacity for Polyetherimide Nanocomposites with Hierarchically Structured Nanofillers

Enhancement of Energy Storage Performance of PMMA/PVDF Composites by Changing the Crystalline Phase through Heat Treatment

Enhanced High‐temperature Energy Storage Performance of All‐organic Composite Dielectric via Constructing Fiber Reinforced Structure

Microstructure and Properties of Poly(butylene Terephthalate)/poly(ethylene Terephthalate) Composites Based on Carbon Nanotubes/graphene Nanoplatelets Hybrid Filler Systems

Study on the Design, Preparation, and Performance Evaluation of Heat-Resistant Interlayer-Polyimide-Resin-Based Neutron-Shielding Materials

Mechanically strong hierarchical nanosystem for fire protection and electromagnetic interference shielding