Abstract:Scanning Thermal Microscopy (SThM) is one of the most universal methods for probing heat conductivity, interfacial thermal resistance and local temperature of materials and devices with nanoscale resolution. SThM uses a temperature sensitive heated probe with an apex of lateral dimensions ranging from a micrometre down to few nanometers that can contact a studied material or a nanoscale device at an arbitrary point on its surface. The tip-sample contact results in a heat flow from the heated tip to the sample - Qts that reduces a heater temperature Th, that is constantly monitored using a sensitive electronic circuit. SThM primary output signal is the heat flow Qts or a closely related parameter - total heater-sample thermal conductance Gts = Qts/(Th-Ts) where Ts is the temperature of the sample. As the tip scanned in a raster way across the sample surface, SThM output produces “thermal” maps reflecting spatial variations in the local sample thermal conductivity ks with the lateral resolution down to a few nanometers (1). A major challenge is the quantitative interpretation of SThM “thermal” signal as ks is fundamentally entangled with the tip-sample interfacial thermal conductance gif that directly depends on the geometry of the tip-surface contact, a generally unknown value that can also vary significantly during SThM measurements. In this paper we describe three linked approaches that allow to eliminate major variabilities in the SThM measurements as well as produce quantitative measurements of nanoscale thin layers of materials. First, we control the temperature of the sample Ts and the microscope base Tm via actively controlled Peltier heating/cooling elements with ~10 mK precision significantly improving the reproducibility of SThM signal by approximately 10 fold. Secondly, we use simultaneous measurement of shear forces and heat flow between the probe (2). As shear forces directly proportional to the contact area, the correlation observed allowed us to confirm the true ballistic nature of heat transport via nanoscale contacts in such a system, suggesting that even large – sub-micrometer sized contacts are composed by a multiple nanoscale junctions with the size below the mean-free-path of the heat carriers. Shear forces SThM allowed us to eliminate dependence of the SThM output on the most difficult to determine parameter – tip-surface contact geometry. Finally, we present a new paradigm of measurement of thermal conductance in the nanoscale thin layers of materials by producing a nanoscale cross-section of the material or device via SPM-friendly Ar ion polishing producing near-atomically low-angle wedge-shaped flat sections (3), followed by the SThM measurements of total thermal conductance Gts as a function of the wedge thickness t. The decrease of the thermal conductance as a function of edge thickness dGts/dt allows to exclusively determine thermal conductivity of the sample kts, eliminating necessity to know either the tip-sample interfacial thermal conductance gif or layer-substrate thermal conductance, two notoriously unknown parameters that render majority of SThM measurements to be merely qualitative.

Scanning thermal microscopy and its applications for quantitative thermal measurements

A Review on Principles and Applications of Scanning Thermal Microscopy (SThM)

A Comprehensive Review for Micro/Nanoscale Thermal Mapping Technology Based on Scanning Thermal Microscopy

Measurements of nanoscale thermal properties of materials via Scanning Thermal Microscopy (SThM):Challenges and solutions

Thermal conductivity measurements of thin films by non-contact scanning thermal microscopy under ambient conditions

Thermal imaging by scanning photothermal radiometry

DISCUSSION ON THERMAL CONDUCTIVITY MEA- SUREMENTS ON A MICRO-SCALE USING SCANNING THERMAL MICROSCOPE

Quantitative Measurement of Thermal Conductivity by SThM Technique: Measurements, Calibration Protocols and Uncertainty Evaluation

Nanoscale spatial resolution probes for Scanning Thermal Microscopy of solid state materials

Nanoscale resolution immersion scanning thermal microscopy

Nanoscale thermometry under ambient conditions via scanning thermal microscopy with 3D scanning differential method.

Where did you come from and where are you heading to, thermal analysis of heating effects?

Realizing the nanoscale quantitative thermal mapping of scanning thermal microscopy by resilient tip-surface contact resistance models.

Nanoscale thermal conductivity of Kapton-derived carbonaceous materials

Transformer bridge-based metrological unit for scanning thermal microscopy with resistive nanoprobes

Experimental setup for thermal measurements at the nanoscale using a SThM probe with niobium nitride thermometer

Developments on Thermometric Techniques in Probing Micro- and Nano-heat

Quantitative Thermal Imaging of Single-Walled Carbon Nanotube Devices by Scanning Joule Expansion Microscopy.

Radiative heat transfer between dielectric bodies

Frequency domain measurements of thermal properties using 3omega-Scanning Thermal Microscope in a vacuum environment

Near-field radiation analysis and thermal contact radius determination in the thermal conductivity measurement based on SThM open-loop system