Abstract:Research on water quenched silicomanganese slag (WQSMS) has primarily focused on grinding it into micro-powder to be used as auxiliary cementitious materials or to synthesize alkali-activated cementitious materials. However, there is a lack of research on utilizing WQSMS as fine aggregates instead of natural aggregates. Although its properties are similar to granulated blast furnace slag (GBFS), most studies investigating the use of GBFS as fine aggregates have mainly focused on mechanical properties rather than microstructure analyses. Meanwhile, to make full use of industrial solid waste, reduce CO2 emissions, and save energy consumption, solid waste cementitious material based on steel slag (SS), desulphurized gypsum (DG), and GBFS, as well as WQSMS as fine aggregate to replace ISO standard sand and washed-out sand (WOS) in various proportions(0%, 25%, 50%, 75%, and 100%) to prepare mortar and concrete, respectively. Analyses of workability, mechanical properties, and microstructure were carried out, and the improvement of mechanical properties of WQSMS was analyzed by SEM-EDS, SEM-BSE, and the microhardness test. The results show that with the increase of WQSMS, the workability of mortar and concrete decreased, while the mechanical strength increased first and then decreased. The mechanical strengths of them reached the peak when the WQSMS addition reached 50%. The flexural and compressive strengths of the mortar increased by 40% and 9.7%, respectively, while the tensile splitting strength and compressive strength of the concrete increased by 11.9% and 3.4%, respectively. The microstructure of the interfacial transition zone(ITZ) was greatly enhanced by WQSMS, which decreased the porosity by 10.49%, decreased the thickness by 27.27%, and increased the microhardness by 11.0%. However, when the content surpasses 50%, the mechanical strength of mortar and concrete declined due to the loose porosity and poor mechanical strength of WQSMS, and there was insufficient cementitious material to fill these holes. Nonetheless, with 100% content, the mortar maintained its high-performance status, with a flexural strength of 8.0 MPa and a compressive strength of 47.9 MPa, and the concrete still fulfilled the specifications of regular concrete C40. Both the fine aggregate and the cementitious material were composed of solid waste, showing potential environmental benefits and interesting green products for future studies.

Development of Composites from Iron-Rich Galvanized Sludge with Slag Based Cementitious Material and Waste Foundry Sand

Preparation of steel slag-based cementitious materials compounded with GBFS and phosphogypsum: mix design, hydration, and microstructure characteristic

Composite Materials with Glass Fiber Waste and Blast Furnace Slag

Study on the Alkali–Sulfur Co-Activation and Mechanical Properties of Low-Carbon Cementitious Composite Materials Based on Electrolytic Manganese Residue, Carbide Slag, and Granulated Blast-Furnace Slag

Effect of carbide slag and steel slag as alkali activators on the key properties of carbide slag-steel slag-slag-phosphogypsum composite cementitious materials

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Feasibility of Preparing Steel Slag–Ground Granulated Blast Furnace Slag Cementitious Materials: Synergistic Hydration, Fresh, and Hardened Properties

Resource utilization of solid waste from steel industries in cement-based cementitious materials: Mechanical properties, hydration behaviors, and environmental impact

Utilization of carbide slag-granulated blast furnace slag system by wet grinding as low carbon cementitious materials

Study on the properties of alkali-activated ferrochrome slag paste filling materials prepared from multiple industrial solid wastes

Development and characterization of grinding sludge-reinforced aluminum-based composite by friction stir process technique

Effects of Steel Fibers (SF) and Ground Granulated Blast Furnace Slag (GGBS) on Recycled Aggregate Concrete

Green concrete with ground granulated blast-furnace slag activated by desulfurization gypsum and electric arc furnace reducing slag

Mechanical properties and chemical microscopic characteristics of all-solid-waste composite cementitious materials prepared from phosphogypsum and granulated blast furnace slag

Sustainable Utilization of Waste Pumice Powder in Slag-Based Geopolymer Concretes: Fresh and Mechanical Properties

Insight into the performance of composite binder with high-volume steel slag, blast furnace slag and desulfurization gypsum

Enhancing Concrete Performance with Waste Foundry Sand Using Ternary Blended Mixes of Ordinary Portland Cement, Silica Fume, and Ground Granulated Blast Furnace Slag

Sustainable engineered geopolymer composites: A study on the potential of fly ash, BOF slag, and iron ore tailings

Enhancement of ultra-fine slag on compressive strength of solid waste-based cementitious materials: Towards low carbon emissions

Effect of water quenched silicomanganese slag as fine aggregate on mechanical properties and microstructure characteristics of solid waste-based mortar and concrete