Abstract:A collagen‐based porous bioink, formed through a process of whipping and centrifugation, facilitates the fabrication of a cell‐laden hierarchical porous structure for tissue engineering. This structure enhances various cellular activities of the laden adipose‐derived stem cells, and the bioink, possessing both printability and bioactivity, shows considerable potential for various tissue engineering applications. In bioprinting procedures, bioinks typically comprise hydrogels, necessitating a balance between printability and bioactivity. Achieving good printability requires a relatively high hydrogel viscosity, but this can reduce bioactivity due to poor cell‐to‐cell interactions of the encapsulated cells. Therefore, developing hydrogels with excellent printability and bioactivity is a significant challenge in bioprinting. Here, a collagen‐based bioink with excellent printability and bioactivity is developed. The bioink is prepared through a two‐step process: first, by subjecting the bioink to whipping to create a non‐homogeneous porous structure, and subsequently, by employing centrifugation to refine this porous structure into a uniform and relatively smaller microscale porous structure (with a specific diameter of 15.7 ± 9.2 μm). Using the designed bioink, a hierarchical porous structure is fabricated without any special equipment or supporting/sacrificing materials. To demonstrate the feasibility of the collagen bioink laden with human adipose stem cells, a hierarchical cell construct is fabricated using a bioprinter. The construct exhibits significantly enhanced cellular activities and superior osteogenic differentiation compared to the bioprinted cell constructs using normal collagen bioink. These findings suggest that collagen‐based bioinks, which are both printable and bioactive, hold significant promise for extensive utilization in a variety of tissue regeneration applications.

Enhancing cell survival in 3D printing of organoids using innovative bioinks loaded with pre-cellularized porous microscaffolds

Sacrificial Microgel-Laden Bioink-Enabled 3D Bioprinting of Mesoscale Pore Networks

3D bioprinting optimization of human mesenchymal stromal cell laden gelatin-alginate-collagen bioink

3D bioprinting of a hyaluronan bioink through enzymatic-and visible light-crosslinking

Extracellular‐Matrix‐Reinforced Bioinks for 3D Bioprinting Human Tissue

Enhancing cell proliferation in three-dimensional hydrogel scaffolds using digital light processing bioprinting technology

Development of a clay based bioink for 3D cell printing for skeletal application

Hybrid 3D microfluidic bioprinting for the engineering of cancer models and tissue substitutes

3D Bioprinting of shear-thinning hybrid bioinks with excellent bioactivity derived from gellan/alginate and thixotropic magnesium phosphate-based gels

Strategy to Achieve Highly Porous/Biocompatible Macroscale Cell Blocks, Using a Collagen/Genipin-bioink and an Optimal 3D Printing Process

An Approach for Fabricating Hierarchically Porous Cell‐Laden Constructs Utilizing a Highly Porous Collagen‐Bioink

3D Printing of Cell‐Laden Microgel‐Based Biphasic Bioink with Heterogeneous Microenvironment for Biomedical Applications

Direct 3D Printed Biomimetic Scaffolds Based on Hydrogel Microparticles for Cell Spheroid Growth

3D bioprinting of dense cellular structures within hydrogels with spatially controlled heterogeneity

Microtissue‐Based Bioink as a Chondrocyte Microshelter for DLP Bioprinting

Extrusion of Cell Encapsulated in Boron Nitride Nanotubes Reinforced Gelatin—Alginate Bioink for 3D Bioprinting

Extrusion bioprinting of cellular aggregates improves mesenchymal stem cell proliferation and differentiation

Embedded Bioprinting of Breast Tumor Cells and Organoids Using Low Concentration Collagen Based Bioinks

Three-dimensional bioprinting using a coaxial needle with viscous inks in bone tissue engineering - An In vitro study

Optimization of collagen type I-hyaluronan hybrid bioink for 3D bioprinted liver microenvironments

Selection and Optimization of a Bioink Based on PANC-1- Plasma/Alginate/Methylcellulose for Pancreatic Tumour Modelling