Abstract:To control underwater acoustic radiation of ships and protect against detection, coatings are attached to the vibrating wet surface of the hulls. Coatings with different pores or scatterers enclosed will attenuate vibration and suppress sound radiation with different mechanisms. However, there are very few experimental studies concerning vibration measurement of a coated structure in water, mainly due to the water environment. A compromised way to reveal the attenuation mechanism is to measure the vibration in an anechoic chamber. A stiffened plate covered by a rubber coating with multi-layered periodic porous is measured by a LDV scanning system in this study, which is aimed to minimize added mass effect of contact measurement. Comparative measurements on bare stiffened plate and stiffened plate covered with solid rubber are also carried out. Vibration transmission from the stiffened plate to the coatings as well as vibration modes on the radiating surface for the three tested objects is obtained. The vibration and sound attenuation mechanism of the proposed rubber coating is unveiled. To control underwater sound radiation of ships or submarines, acoustic coatings are developed, which is covered on the wet surface of hulls to reduce vibration or attenuate under-water acoustic radiation. Acoustic coatings can be classified into anechoic layer, decoupling layer, damping layer and the like. The main functions of anechoic layer are absorbing the incident acoustic waves for protecting against detection by active sonar. Decoupling layer isolates the fluid from the vibrating of the structure to reduce vibration and to attenuate sound radiation. Damping layer usually employed to reduce vibration. This investigation is concentrated on a layer which is designed to serve the sound and vibration insulation purpose, aiming at lowering the underwater sound radiation. For the purpose of underwater acoustic attenuation, the material should be compatible with water in terms of the acoustic impedance. Use of multilayer absorbers has become increasingly important in noise abatement. These layers are made of rubber material for its convenience of manufacturing and prominent damping. The solid rubber is not an ideal one because of its impedance match with that of water and the artificial rubber is proved to be the best. Therefore, the rubber material is designed with internal structures. Among them, two kinds of internal structures are studied extensively. One is with voids filled with air; the other one is cavities filled with scatterers (1). The vibration and sound insulation mechanisms are different for them. Some of the studies are summarized as follows. Maidanik and Tucker (2) studied the relations between coupled vibration and sound radiation for coated panels immersed in fluid media. Foin et al. (3) presented a coupled model to study the vibration and acoustic response of a rectangular plate covered by a decoupling coating and immersed in a heavy acoustic fluid. Berry et al. (4) analyzed the vibroacoustic of a finite rectangular plate covered with a layer of decoupling material and immersed in a heavy fluid based on three-dimensional theory of elasticity. Tao (5) built the vibroacoustic coupled model to predict the noise reduction performance of an infinite bare plate covered with a void decoupling layer. From the literatures above, it can be seen

Theory and numerical method for the effects of hydrostatic pressure on sound absorption of underwater acoustic coatings with air cavities

Ultrathin and Pressure-Resistant Meta-Coating with Embedded Tree-Shaped Acoustic Black Hole for Broadbnd Low-Frequency Underwater Sound Absorption

Investigation on Low-Frequency and Broadband Sound Absorption of the Compact Anechoic Coating Considering Hydrostatic Pressure

Effect of Poisson's Loss Factor of Rubbery Material on Underwater Sound Absorption of Anechoic Coatings

Study on Characteristics of Sound Absorption of Underwater Visco-elastic Coated Compound Structures

Numerical Analysis and Experimental Study of Sound Insulation Performance of Underwater Viscoelastic Coated Compound Structures

Experimental and numerical analysis of rubber isolator dynamic stiffness under hydrostatic pressure

Underwater Anechoic Layer with Parallel Metallic Plate Insertions: Theoretical Modelling

On the Accuracy and Optimization Application of an Axisymmetric Simplified Model for Underwater Sound Absorption of Anechoic Coatings

A low-frequency anechoic coating under high hydrostatic pressure by pressure balancing strategy

Sound absorption mechanism of underwater anechoic coating with spherical cavities

Optimization of Decoupling Performance of Underwater Acoustic Coating with Cavities Via Equivalent Fluid Model

Analysis of underwater sound absorption of visco-elastic composites coating containing micro-spherical glass shell

Numerical Simulation and Experimental Study of Underwater Compound Structures Containing Honeycomb Interlayer

Influence of Solid Rubber Coating on the Response of Floating Structure to Underwater Shock Wave

Deep-subwavelength and Hydrostatic-Pressure-resistant Meta-Absorber for Broadband Low-Frequency Underwater Sound

Dynamical Mechanical Property of Viscoelastic Materials and Its Effect on Acoustic Absorption of Coating

LDV-based Vibration Measurement of a Stiffened Plate Covered by a Rubber Coating with Multi-Layered Periodic Porous in Air

Underwater Sound Absorption Characteristics of Water-Saturated Porous Materials

Analysis of Decoupling Mechanism of an Acoustic Coating Layer with Horizontal Cylindrical Cavities

A Plane Strain Elasticity Model for the Acoustical Properties of Rib-Stiffened Composite Plates