Abstract:Light alloys are being increasingly investigated as alternatives to ferrous-based engineering components, based on weight considerations. However, in-service applications of such light alloy components often require a surface modification step to enhance their wear and corrosion responses for improved functionality. Thermally sprayed cermet coatings offer an enhanced resistance to wear and corrosion. This work investigates WC-CoCr coatings deposited using two different feedstocks comprising fine and coarse powder size distributions on aluminum alloy and steel substrates using high-velocity air-fuel (HVAF) and high-velocity oxy-fuel (HVOF) spray techniques. The WC-CoCr coatings were HVAF sprayed at various parameters to investigate the relationship between the processing conditions, microstructure, and performance. Microindentation, dry sliding wear, dry sand abrasion, cavitation erosion, and corrosion tests were conducted to assess the performance of the coatings. Despite the qualitative similarities in the microstructures of the coatings, the measured microindentation hardness values were observed to vary, and coatings deposited with higher particle impact velocities showed the highest microhardness between 1400 and 1600 HV0.3. For the three categories of wear investigated, the HVAF coatings showed better resistance than the HVOF coating investigated in this study. The estimated average specific wear rate (SWR) due to sliding wear of the HVOF coating was ~ 16.7 ± 4.0 × 10 −8 mm 3 /Nm compared to that of the most resistant HVAF coating, which exhibited a SWR of ~ 1.7 ± 0.6 × 10 −8 mm 3 /Nm. The cumulative mass loss rate due to the abrasive wear on the HVOF coating reached ~ 1.11 mg/min compared to ~ 0.76 mg/min of the most abrasion-resistant HVAF coating. All coatings showed similar corrosion resistances under the investigated conditions. The combination of wear and corrosion performance of the respective coatings could provide insight into the coating selection for intended applications.

Impact of HVOF sprayed Vanadium Carbide (VC) based novel coatings on slurry erosion behaviour of hydro-machinery SS316 steel

Slurry erosion behaviour and mechanism of HVOF sprayed micro-nano structured WC-CoCr coatings in NaCl medium

Corrosion and erosion performance of HVOF/TiAlN PVD coatings and candidate materials for high pressure gate valve application

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Corrosion–Cavitation Erosion Improvement of Marine Steel by High-Velocity Oxy-fuel-Sprayed Vanadium Carbide Coatings and Polytetrafluorethylene Topcoat

Resistance of HVOF-Sprayed Cr3C2-25NiCr and WC-10CO-4Cr coatings to cavitation and erosion by mud jetting

Experimental Investigations on Erosion-Corrosion Characteristics of HVOF-Sprayed WC-10% Ni Coatings Deposited on Aluminum Alloy

Wear and Corrosion of HVAF and HVOF-Sprayed WC-CoCr Coatings on Aluminum Alloy

Cavitation Erosion Investigations of Hard Carbide and Nitride Based Novel Coatings Manufactured by Plasma Spraying

HVOF-sprayed surface coating with various compositions of Co-NiCrAlY-Al 2 O 3 to minimize sediment erosion in hydraulic turbines

Enhanced slurry and cavitation erosion resistance of deep cryogenically treated thermal spray coatings for hydroturbine applications

Wear Behaviour of Hard Chrome and Tungsten Carbide-HVOF Coatings

A comparative assessment on the characteristics of HVOF sprayed cermet coatings

The Dry Sliding Wear Behavior of HVOF-Sprayed WC: Metal Composite Coatings

CAVITATION EROSION BEHAVIOR OF WC–Co COATINGS ON TURBINE STEEL DEPOSITED BY COLD SPRAY

Dry Sliding Friction and Wear Performance of HVOF Sprayed WC–Co Coatings Deposited on Aluminium Alloy

Investigations on Tribological and Microstructure Characteristics of WC-12Co/FeNiCrMo Composite Coating by HVOF Process

Comparison of the Resistance to Cavitation Erosion and Slurry Erosion of Four Kinds of Surface Modification on 13-4 Ca6NM Hydro-Machinery Steel

Hydro-abrasive Erosion and Cavitation-Silt Erosion Characteristics of HVOF Sprayed WC-Ni Cermet Coatings under Different Flow Velocities and Sand Concentrations

Investigation on Microstructure, Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC-Co + CR) On Ductile Cast Iron

Characterization and Sliding Wear Behavior of Iron-Based Metallic Coating Deposited by HVOF Process on Low-Carbon Steel Substrate