Abstract:The stiffness of machine tools is a key factor to increase the productivity. The dynamic stiffness dominates the stable cutting conditions, where forced and regenerative chatters do not occur. In general, dynamic stiffness is measured using an impact hammer as it does not require the particular device setting. However, humans should use a hammer and impact control needs skills. To this end, several researches have been conducted to establish automatic excitation methods. To measure the dynamic stiffness of a rotating spindle, authors have developed an electromagnetic biaxial excitation device which can generate biaxial force. This paper presents the measurement result of dynamic stiffness for both the structure and spindle of a five-axis machining center using the developed device. INTRODUCTION For the avoidance of chatter vibrations in machining, chatter mechanism and suppression methods have been studied [1]. One of the well-known techniques is chatter prediction using stability limit diagrams (SLDs), where the relation between the limit of depth of cut and spindle speed is analyzed and shown graphically. For the prediction of the stability limit accurately, it is necessary to measure the precise dynamic compliance of the machine. In general, dynamic stiffness is measured using an impact hammer for its simplicity. However, humans should use a hammer with skills. To this end, several researches have been conducted to establish automatic excitation methods [2-4], which are categorized into contact and contact-less methods. The noncontact excitation method has been developed to analyze the dynamics of rotating spindle. It also can explain the dynamics of machine structure comparably. This paper presents the analysis of both the structure and spindle of a five-axis machining center using the developed device. Through the measurement tests, anisotropic in stiffness were investigated. MEASUREMENT SYSTEM Figure 1 (a) shows the schematic of a developed biaxial electromagnetic excitation device [5]. The device consists of iron cores, coils, yoke (housing) and its cross-section view is shown in Fig. 1 (b). A dummy tool attached to the spindle is inserted into the hole, facing to the coils with air-gap. Giving current to two coils generate magnetic flux, flown to the surface of the dummy tool and the yoke. Thus, two coils can produce a single attraction fore in a single direction. Eight coils generate biaxial force (x and y) in plus and minus directions. Yoke diameter:φ220 mm Hight : 160 mm (a) Isometric view (b) Sectional view Figure 1: Schematic of electromagnetic excitation device. Figure 2 shows the experiment and measurement system. The excitation device was installed on the machine tool table of a five-axis machining center, where a dynamometer was placed on the table to measure attractive forces. The dummy tool that integrates a holder interface was attached to the spindle. Displacement sensors were installed at the upper case of the housing, measuring the holder displacement of the dummy tool in the xand the y-directions. A control PC sent a swept-sine current command to an amplifier that gives coil current to Coil Housing Iron core 22.5° 22.5°

Analysis of Dynamic Characteristics for Machine Tools Based on Dynamic Stiffness Sensitivity

Dynamic Sensitivity Analysis of Complex Structure Based on FEM

Inherent Characteristics and Dynamic Response Analysis of High-Speed Cutting-Tool System

Characterizing machine tool spatial stiffness and predicting accuracy

Testing and Analysis of the Dynamic Characteristics of Vertical Machining Centers

Dynamic Analysis and Optimization of Machine Tool in Consideration of Joint Parameters

Analysis of dynamic characteristics of five‐axis CNC machine tool

Nonlinear dynamic modeling and vibration analysis of whole machine tool

On obtaining machine tool joints stiffness by integrated modal analysis

Stiffness Analysis of Machine Tools Using Finite Element Method

Optimal Design of the Vertical Machining Center Based on Stiffness Analysis

Experimental Research on Dynamic Performance of Some Gantry Machining Center Structure

Stiffness Analysis and Optimization of a Hybrid Machine Tool Based on the Stiffness Matrix

Stiffness Analysis of Gantry Hybrid Machine Tools

Modal and Harmonic Reponse Analysis and Evaluation of Machine Tools

Static stiffness research of a hybrid machine tool based on the element stiffness matrix

Hybrid multibody system method for the dynamic analysis of an ultra‐precision fly‐cutting machine tool

Milling Stability Prediction of a Hybrid Machine Tool Considering Low-Frequency Dynamic Characteristics

Structural dynamic design optimization and experimental verification of a machine tool

INVESTIGATION OF DYNAMIC STIFFNESS OF MACHINE TOOL WITH ELECTROMAGNETIC BIAXIAL EXCITATION DEVICE

Experimental study of machining system: dynamic characterization